Kscs25fvms Parts

Ice dispenser not crushing properly? This blade mounting block secures crusher blades in the ice container head, eliminating noise and uneven crushing.

Support plate kit for refrigerators. Includes left and right side mounting plates. Replace if cracked, broken, or missing to restore proper support.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

Wire tie secures and organizes internal wiring harnesses in your appliance. Replace if the original tie is broken, cracked, or missing during repairs.

Replacement door hinge for your refrigerator. Installs on the cabinet to support door weight. Needed when hinge is broken, cracked, or worn out.

The Dispenser Motor is an OEM part for Whirlpool refrigerators. It is a crucial component that powers and operates the water and ice dispensing system, allowing users to conveniently access chilled water, cubed ice, or crushed ice from the refrigerator door.

Causes of a bad dispenser motor may include electrical failures, mechanical wear and tear, or physical damage from impact or moisture.

Symptoms of a faulty Dispenser Motor include:

• No water or ice being dispensed from the refrigerator door
• Intermittent or inconsistent water or ice dispensing
• Leaks or drips from the dispenser area
• Unusual noises or grinding sounds when attempting to dispense

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models. 

Ice maker not working or frosting over? This protective cover shields the control module from debris and moisture. Easy 30-minute DIY installation.

Replaces a worn or heat-damaged refrigerator light socket to restore interior lighting. Install when bulbs won't light despite replacement. Confirm fit by model number.

Includes cover part number 2305219

Small metal washer for refrigerator assemblies. Distributes load under bolts and nuts to keep components secure. Replace if lost, damaged, or worn.

Shelf cover assembly that installs above the deli/meat drawer in your refrigerator. Replace if cracked, broken, or missing to restore support and function.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

Round cap button that covers the water filter housing on your refrigerator. Replace if cracked, broken, missing, or no longer snaps securely into place.

Ice cubes jamming or not releasing from your ice maker? This stripper arm sweeps ice from the mold for proper harvest. Simple DIY fix in minutes.