Ksm5op Parts

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet operation. Replacing a worn bearing restores proper alignment and helps prevent noise and premature wear on connected parts.

• Provides a low-friction surface for smooth rotation
• Helps keep the rotating component centered and stable
• Reduces vibration and operating noise
• Common failure signs: grinding/squealing, wobble or play, rough or intermittent rotation

• Disconnect power; also shut off water or gas supply if applicable
• Access the assembly per your model's service information and note part orientation before removal
• Inspect the shaft/hub and any spacers or seals for wear; replace related worn components
• Seat the bearing squarely—do not force; apply only manufacturer-specified lubricant if called for in service literature

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Fix a mixer that won't turn on or has burnt electrical smell. This motor field assembly controls variable speed. Replaces worn electrical components.

If your mixer runs intermittently or loses power, a cracked or missing brush holder cap may be letting the carbon brush slip. Simple threaded repair.

If your mixer bowl won't stay in place or wobbles during mixing, this retainer clip secures it properly. Simple DIY fix takes just minutes to install.

Fix a mixing bowl that won't lock in place or keeps sliding during use. This retaining pin secures the bowl clip to keep your bowl firmly seated.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.

5-quart stainless steel bowl for bowl-lift stand mixers. Replace if warped, dented, or worn. Verify your model number for proper fit before ordering.

Fix a mixer that won't start, slows down, or makes grinding noises. This armature (motor rotor) restores reliable operation when worn or burned.

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)

This is a flat washer used in the drive assembly of a stand mixer. It sits between moving components to reduce friction and prevent wear on mating surfaces. Replace this washer if the mixer is making unusual noises, vibrating excessively, or if the original washer is worn, cracked, or missing.

Mounting screw secures internal brackets and panels in mixers. Replace if missing, stripped, or damaged to prevent loose components and rattling.

Fastens internal components in your stand mixer. Replace this screw if stripped, corroded, or missing to secure panels and brackets properly.

Replacement 5-quart polished stainless steel mixing bowl for KitchenAid bowl-lift stand mixers. Installs on lift mechanism with flat handle design.

Note: This is for Professional Models

Fix a mixer that won't engage or slips during operation. This cam restores proper mechanical linkage timing. Straightforward DIY replacement part.