Kudco31vbl4 Parts

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Includes two screws, two clamps, and undercounter mounting brackets.

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

To order seal use WP8268340.

This replacement screw secures appliance components in place. Swapping a stripped, rusty, or missing fastener restores a tight fit for panels, brackets, and handles, helping reduce vibration, rattling, and premature wear.

• Secures panels, brackets, trim, or hardware to the appliance frame
• Replaces missing, stripped, or corroded fasteners that no longer hold
• Helps eliminate looseness, rattling, or misalignment
• Restores proper fit and finish after service

• Disconnect power; shut off water supply if servicing a dishwasher.
• Match thread and length to the original screw before installing.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• When applicable, replace paired screws together for even clamping.

Also Order Spray Arm Seal

This dishrack organizes and supports dishes inside the dishwasher during wash cycles. Replacing a damaged rack restores smooth loading, keeps items upright, and helps prevent rust stains or snags from broken tines or flaking rack coating.

• Holds and organizes plates, bowls, and cookware during wash and rinse cycles
• Keeps items spaced and upright to promote spray coverage and drainage
• Slides in and out on the rails when the rack is straight and intact
• Common failure signs: rusting/chipping coating, broken or bent tines, cracked or warped wire frame
• Needed if dishes won't stay put or the rack binds when moving on the tracks

• Disconnect power at the breaker and turn off water before servicing interior parts
• Open the door, extend the rack, and remove rail end caps to release the rack
• Transfer any clip-on components from the old rack to the new rack as needed
• Seat the rack on the rails, reinstall end caps, and check for smooth operation

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

Almond. Size: 13 oz. can. Acrylic appliance paint.

This control panel replaces a cracked, worn, or unresponsive console so your appliance can reliably accept cycle and option selections again, restoring a clean appearance and smooth button action.

• Provides the interface area for selecting cycles and options
• Houses and aligns user-interface components and mounting hardware
• Protects and routes the UI connector/ribbon, when present
• Restores proper fit and finish on the front/top of the unit
• Typical symptoms: cracked or broken console, buttons binding or sticking, worn labels, or selections not registering when the touchpad is integrated into the console on your model

• Disconnect power to the appliance before servicing
• Remove screws to access the console; note hardware locations and wire/ribbon routing, and use care around sharp edges
• Handle any ribbon/IDC connectors by the stiffener; seat fully and level
• Transfer any reusable clips, brackets, or overlays/nameplates from the old panel; test keys before final reassembly

This latch actuator links the door lock mechanism on select ranges and wall ovens, engaging and releasing the door as designed. Replacing a worn or bent actuator restores smooth latch movement and reliable door locking during normal use and self-clean cycles. What it does:

• Transfers motion within the latch assembly to lock and unlock the oven door
• Helps the door lock engage for self-clean and release when complete
• Addresses issues like a door that won't lock/unlock or latch fully
• Can resolve incomplete self-clean cycles caused by a misaligned or damaged latch linkage

• 1 latch actuator

• Disconnect power at the breaker before servicing
• Access the latch assembly per your model's service/parts diagram
• Note the actuator's orientation and any linkage/spring positions before removal
• Verify smooth manual latch operation before reassembling and restoring power