Kudp01lbl2 Parts

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.

• Screens large food particles and debris from the pump/chopper inlet
• Helps maintain proper water circulation and consistent cleaning performance
• Reduces risk of pump damage or noisy operation from debris
• Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack and spray arm; access the sump/accumulator area per your model
• Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
• Reassemble and ensure the screen sits flat with no gaps

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

Color: gray. Measures about 3 inches wide by 1-1/2 inches high.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

Color: light gray. Measures about 3 inches high by 6 inches deep.

The Rinse Aid Cap seals the dishwasher dispenser's rinse aid reservoir. Replacing a worn, cracked, or missing cap prevents leaks and evaporation, helping the dispenser meter rinse aid properly during the final rinse.

• Provides a tight seal for the rinse aid reservoir
• Helps ensure correct rinse aid dispensing in the final rinse cycle
• Symptoms include: cap cracked or missing; rinse aid leaking or depleting quickly; residue or streaks near the dispenser

• Disconnect power to the dishwasher before servicing.
• Remove the old cap and clean any buildup around the dispenser opening.
• Hand-install the new cap until snug; do not overtighten.
• Fill the reservoir and check for leaks around the cap.

This user interface is the electronics behind a full-door console dishwasher panel. It reads your button selections and communicates with the main control so cycles start and options respond reliably.

• Interprets keypad inputs from the console and sends commands to the control board
• Helps restore proper control of wash cycles, options, and start/delay functions
• Common symptoms: unresponsive or intermittent buttons, no console lights, can't start from the panel, erratic beeping/stuck-key behavior
• Built for full-door (full-console) configurations used on select models

• Disconnect power at the breaker; turn off the water supply
• Remove inner door/console screws to access the UI; support the panel to avoid straining wires
• Handle the board with ESD care; transfer any mounting clips/brackets and seat ribbon cables/connectors fully and correctly
• Reassemble the door and test console operation before running a full cycle

Color: gray. Measures about a 1/2 inch wide by 3 inches high by 1-1/2 inches deep.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This control panel mounts on the appliance's door and provides the push-button interface for selecting cycles and options. Replacing a cracked or unresponsive console restores reliable button operation and a clean, factory look. What it does:

• Houses the user-interface buttons and indicator windows used to select cycles/options
• Provides a rigid mounting surface for the door's UI components
• Helps protect internal wiring at the top of the door
• Typical symptoms: buttons don't respond or work intermittently, unit won't start when Start/Resume is pressed, selections change unpredictably, or the console is cracked/loose

• One console assembly

• Disconnect electrical power; turn off the water supply if needed
• Open the door and remove the inner-door perimeter screws to separate the console from the inner panel
• Note and transfer any reusable parts from the old console as required; make secure, straight ribbon/harness connections
• Reassemble the door, restore power, and run a quick function check before final tightening

To order seal use WP8268340.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required