Kuds20fxss3 Parts

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

Size: 8-32 x 1/2 inch.

The Gasket is an OEM part for Whirlpool dishwashers. This gasket seals the gap between the dishwasher door and the main tub, preventing water from leaking out during the wash cycle. It ensures a watertight seal that helps maintain the efficiency and performance of the dishwasher.

 Over time, the gasket can deteriorate due to regular use, exposure to heat, and contact with detergents. A faulty gasket can lead to water leaks, which may cause damage to surrounding cabinetry and flooring.

Symptoms of a bad dishwasher gasket include:

• Water leaking from the bottom or sides of the dishwasher door
• Visible cracks or tears in the gasket
• The dishwasher door not closing properly
• Increased noise levels during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This seal kit is for the main tub. It goes around the pump housing.

Note: There are four wheel assemblies includes with this rack. The flexible tine rows are not included. This is a lower dishrack assembly for a dishwasher. This part holds the dishes during the washing and drying cycles. Note that this is only the lower dishrack assembly and the upper dishrack assembly is sold separately. Over time, the lower dishrack assembly may begin to rust or the coating may wear off. It is also possible that sections of the part could break due to degradation over time. If this happens, the entire lower dishrack assembly will need to be replaced. The lower dishrack assembly is compatible with dishwashers that are manufactured by the Kenmore, KitchenAid, and Whirlpool brands. It comes straight from the manufacturer and is sold individually. It's a genuine, high-quality, and durable OEM part.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

This bi-metal actuator heats and flexes to trip the detergent cup latch during the wash cycle, releasing detergent at the proper time for effective cleaning performance. What it does:

• Heats and bends to mechanically trigger the detergent dispenser door
• Restores proper, timed detergent release during the main wash
• Common symptoms: detergent left in the cup after a cycle, dispenser door never opens, or intermittent/late opening

• One bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Access from the inner door panel; remove screws to reach the dispenser area
• Transfer wires one at a time and mount the actuator in the original position
• Reassemble the door and run a test cycle to ensure proper dispenser operation

This replacement silverware basket holds forks, knives and spoons in the dishwasher lower rack so utensils stay upright and separate for better cleaning and easier unloading. It's a direct-fit interior basket designed to restore secure utensil loading. What it does:

• Keeps silverware and small utensils contained so pieces don't fall through or block the spray arms
• Separates items to improve water flow and cleaning coverage
• Prevents loose utensils from banging and potentially damaging dishes
• Replaces cracked, broken, or missing baskets that allow utensils to shift during the cycle

• Drop into the lower rack — no tools required for typical swap-out
• Position basket so it sits flat and does not interfere with rack movement or spray arm rotation
• Avoid overloading; place sharp utensils point-down or bundle separately to reduce hazard when unloading
• For appliance repairs beyond simple replacement, disconnect power and water before servicing