La780p Parts

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

This mechanical washer timer controls the sequence and duration of every cycle. Replacing a worn timer can restore proper advancing and reliable fill, wash, drain, and spin operation. What it does:

• Controls timing for fill, wash/agitate, drain, and spin steps
• Routes power to the motor, pump, and inlet valves at the correct times
• Advances the control dial automatically through each stage
• Failure can present as won't start, won't advance or stops mid-cycle, or skips functions (fill/agitate/drain/spin)

• 1 timer assembly

• Disconnect power before servicing
• Access the timer in the control console; remove the back cover, knob/retainer, and mounting screws as needed
• Transfer wires one at a time from the old timer to the new to maintain positions
• Reassemble and run a short cycle to verify proper operation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This bolt is a genuine Whirlpool part, sold individually. It can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This bolt fastens parts to one another in conjunction with a nut so that they do not come loose while the washing machine vibrates when it is in operation.A bolt might be easily lost or misplaced as it is a small part that might go missing without any noticeable symptoms. Additionally, a bolt might be stripped through general wear and tear or as a result of a direct impact collision with a hard object that warps the component beyond functionality. If any of these things occur, the bolt should be replaced by this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bolt is compatible with the following appliance brands: Whirlpool, Maytag, International, and Jenn Air.

This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.

• Seals the injector-to-liner/fill-tube connection to stop water seepage and air leaks
• Helps prevent frost/ice buildup near the injector area and fill tube freeze-ups
• Addresses issues from a cracked, shrunken, or missing seal
• Common symptoms: water drips at the back/freezer wall and frost near the fill opening

• Disconnect power and shut off the water supply before servicing
• Access the injector area (rear of freezer or cabinet, depending on model)
• Remove the old seal; press the new seal fully and evenly into place
• Reassemble, restore water/power, and check for leaks and proper fill

This stop lug is a small, molded limiter that prevents over-travel of a moving control or mechanism in your washer, helping components stop in the correct position for consistent, reliable operation.

• Acts as a positive stop to limit movement of a mating part
• Helps maintain proper alignment and protects components from over-rotation
• Symptoms of a worn or missing lug can include excessive play, over-travel, or a control that doesn't stop where it should
• Visible damage or a missing lug indicates replacement is needed

• Disconnect power and water supply before servicing
• Access the mounting area and note the original orientation
• Seat the new lug fully and secure per the original configuration
• Reassemble and test that the mechanism stops at the intended position

Size: 10-16 x 5/8 inch.

This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.

• Provides front support and height adjustment to level the unit
• Helps reduce rocking, vibration, and rattling during operation
• Replaces a worn, broken, missing, or stripped front foot
• Helps ensure doors or drawers align and close properly when leveled

• Disconnect power and, if applicable, shut off water/gas before servicing
• Protect flooring; carefully tip or brace the appliance to access the front foot
• Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
• Verify stability, then restore utilities and recheck for level

This transmission pinion is the small drive gear inside the gearcase that meshes with the mating gear to transfer motor power through the drive. Replacing a worn pinion restores smooth operation and reliable torque delivery.

• Transfers rotation from the motor through the gear train inside the transmission
• Helps maintain proper speed and torque to the drive output
• Replaces stripped or broken teeth that cause slipping and chatter
• Typical symptoms: grinding/clicking noises, output that stalls or won't turn, metal shavings in grease

• Unplug the appliance before servicing; allow all moving parts to stop
• Access requires opening the drive housing/gearcase; note the orientation of shims, washers, and spacers
• Clean out old grease/debris and re-pack with manufacturer-approved grease
• Inspect mating gears, bearings, and shafts for wear; replace related parts as needed and follow the service manual for alignment

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

Almond. Size: 13 oz. can. Acrylic appliance paint.