Lat 9704 Aae Parts

This transmission pinion is the small drive gear inside the gearcase that meshes with the mating gear to transfer motor power through the drive. Replacing a worn pinion restores smooth operation and reliable torque delivery.

• Transfers rotation from the motor through the gear train inside the transmission
• Helps maintain proper speed and torque to the drive output
• Replaces stripped or broken teeth that cause slipping and chatter
• Typical symptoms: grinding/clicking noises, output that stalls or won't turn, metal shavings in grease

• Unplug the appliance before servicing; allow all moving parts to stop
• Access requires opening the drive housing/gearcase; note the orientation of shims, washers, and spacers
• Clean out old grease/debris and re-pack with manufacturer-approved grease
• Inspect mating gears, bearings, and shafts for wear; replace related parts as needed and follow the service manual for alignment

This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.

• Controls incoming water to achieve correct fill levels and temperature mix
• Addresses no fill, slow/partial fill, or water seeping into the tub when off
• Replaces valves that are electrically failed or mechanically clogged/sticking

• Disconnect power and shut off both water supplies before servicing
• Have towels ready; relieve hose pressure and note wire/hose locations (take a photo)
• Transfer any mounting parts from the original valve if required; avoid overtightening plastic fittings
• Restore water slowly, check for leaks, and run a test fill

This stop lug is a small, molded limiter that prevents over-travel of a moving control or mechanism in your washer, helping components stop in the correct position for consistent, reliable operation.

• Acts as a positive stop to limit movement of a mating part
• Helps maintain proper alignment and protects components from over-rotation
• Symptoms of a worn or missing lug can include excessive play, over-travel, or a control that doesn't stop where it should
• Visible damage or a missing lug indicates replacement is needed

• Disconnect power and water supply before servicing
• Access the mounting area and note the original orientation
• Seat the new lug fully and secure per the original configuration
• Reassemble and test that the mechanism stops at the intended position

This suspension spring hook connects a tub suspension spring to the washer frame, helping support and center the wash basket. Replacing a worn or missing hook can reduce shaking, banging, and off-balance interruptions during spin.

• Secures one end of a suspension spring to the cabinet/base
• Helps control tub movement and absorb vibration during agitation and spin
• Failure signs include excessive vibration or banging, tub leaning/sagging, or frequent out-of-balance stops

• Disconnect power and water; wear gloves and eye protection
• Access the suspension area per model; support the tub to relieve spring tension
• Use pliers or a spring tool to remove the old hook; note orientation and mounting location
• Seat the new hook fully and ensure the spring is engaged securely before reassembly and testing

This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.

• Connects the washer's drain outlet to the household standpipe or laundry tub
• Molded bend helps position the hose correctly and reduces kinking
• Typical symptoms: water leaking at the back or onto the floor while draining
• Visible splits, soft spots, brittleness, or abrasion on the hose
• Slow or incomplete draining caused by kinks or internal blockage

• Disconnect power and move the washer to access the rear; shutting off water is recommended as a precaution
• Place towels or a shallow pan to catch residual water when removing the old hose
• Transfer and reuse existing clamps/brackets if required; fully seat and secure connections, and route the hose to avoid kinks or rubbing
• Insert the outlet end properly into the standpipe or tub per your model's instructions, then run a quick drain/spin to check for leaks

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

To order indicator lens use WP22001948.

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This pressure switch hose carries air from the washer tub to the pressure switch so the machine can sense and control water level. Replacing a damaged hose restores proper fill control and prevents level-sensing errors. What it does:

• Channels air/vacuum from the tub to the pressure switch so the control can detect water level.
• A cracked, pinched, or collapsed hose may cause overfilling, underfilling, failure to advance cycles, or continuous fill.
• Restores accurate water-level sensing when replacing a worn or damaged hose.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove and replace the hose carefully; avoid kinks, sharp bends, or pinched routing that can impair sensing.
• Use the factory-style connection points and clamps; ensure both ends are seated securely.
• After installation, run a test fill or diagnostic cycle to confirm correct water-level operation and no leaks.

This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.

• Locks into a groove to keep gears, pulleys, wheels, or spacers from sliding off a shaft
• Helps maintain proper spacing and alignment of moving parts
• Common signs of failure: wobbling parts, scraping/rubbing noises, or components that work loose
• Visual clues: deformation, corrosion, or loss of spring tension

• Disconnect power and any utilities to the appliance before service
• Wear eye protection—retaining rings can spring free under tension
• Note the order/orientation of any washers or spacers before removal
• Use appropriate snap-ring or needle-nose pliers and ensure the ring seats fully in its groove

This factory bolt is a direct-replacement fastener used to mount and secure appliance components. Replacing a stripped, rusted, or missing bolt restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Secures components to prevent loosening from vibration and normal use
• Helps maintain proper alignment of parts and assemblies
• Replaces hardware that is stripped, corroded, or lost
• Common symptoms include loose or wobbling parts, vibration, and rattling noises

• Disconnect power and shut off water/gas before servicing
• Compare length and thread to the original fastener; transfer any washers/spacers from the old bolt
• Start by hand to avoid cross-threading; tighten per service manual—do not overtighten
• Apply thread-locking compound or replace companion hardware

Replacement lug stop that limits movement of a mechanical component to prevent over-travel and reduce wear. Restores proper stopping action so doors or internal mechanisms operate more smoothly and safely. What it does:

• Stops or limits travel of a moving part to prevent over-rotation or over-extension.
• Keeps doors, lids or internal linkages from swinging past their intended position.
• Replace if the lug is cracked, worn, broken, missing, or if the mechanism fails to stop or rattles.
• Helps prevent further damage from metal-on-metal contact or excessive movement.

• Disconnect power before starting any repair.
• Basic hand tools and access panel removal may be required to reach the mounting area.
• Inspect adjacent clips, fasteners and mating surfaces; replace any damaged hardware.

This washer timer is the mechanical control that sequences the wash, rinse, drain, and spin operations. Replacing a worn or stuck timer restores proper cycle advancement so loads complete reliably and the machine shuts off as expected.

• Controls and times the fill, wash, rinse, drain, and spin sequences
• Advances the cycle and turns the washer off at completion
• Routes power to the motor, pump, and water valves at the correct intervals
• Common symptoms: cycles won't advance or stop mid-cycle; only some timer positions work; timer knob does not move
• Additional symptoms: runs indefinitely or won't start; no agitation or spin in any cycle

• Disconnect power to the washer before servicing
• Open the control console to access the timer
• Note wire locations or take photos; move the harness to the new timer
• Secure the timer, reassemble the console, and run a test cycle

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

This hex-head sheet metal screw secures appliance panels, brackets, and trim for a tight, rattle-free fit. Replace missing or stripped fasteners to keep covers and components firmly in place and restore proper alignment.

• Fastens sheet-metal parts, brackets, and trim using a hex drive
• Replaces worn, rusted, missing, or stripped screws
• Helps reduce vibration and rattling from loose panels
• Common signs you need this fastener: head or threads stripped, screw won't tighten, panel or handle coming loose

• Unplug the appliance before service; turn off water supply if working near water lines
• Use the correct nut driver or socket to avoid rounding the head
• Replace one fastener at a time to maintain alignment; do not overtighten
• Match screw type/length to the original location as specified by the manufacturer