Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
Connects water supply to the dispenser injector in your washer. Replace if cracked, nicked, or leaking. Installs at the top under the lid assembly.
First the parts showed up as promised in 2 days. Injector fill hose wasn't leaking but replaced to be on safe side. Everything went together just like OEM parts. Cost less then having my appliance guy just walk thru the door at $80.00 Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub. Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.
Called a Maytag repair man, said "the bumpers are no longer available". These little things are actually critical to operation, because the lid safety switch needs to be pressed back far enough to sense that the lid is closed, and without the bumpers, this is a little iffy. I looked up the parts on the internet, came across AppliancePartsPros.com and guess what, the parts were available !! Ordered, delivered on time, installed, and I'm up and running. Now I don't have to hear my wife... Read more
Small drive gear inside the washer transmission gearcase that meshes with mating gears. Replace when worn, stripped, or damaged to restore power transfer.
American appliances are very easy to fix in comparison to imported ones. Just open the washer and take de transmission cover out change the pinion inside removing a simple retainer. In the agitator there is a screw that you loosen it take it out, then de tub and take the shaft out and put a new seal and a new c clamp and reinstall everything back. Top-loading washers are very easy to fix in comparison to front-loading washers that are very difficult to fix. Read more
Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.
We ordered parts from appliance parts pros and I fixed it. Read more
Small metal clip that secures panels, brackets, or tubing in place inside appliances. Replace if bent, fatigued, or missing to restore secure mounting.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.
Washer won't advance through cycles or stops mid-cycle? Timer controls cycle progression and electrical components. Moderate DIY—about 1 hour.
The gentle cycle did work, so I figured that the cycle controller was the problem. I searched on line with the make and model # for parts and found the item with a picture that looked just like the part in my machine, so I bought it, and it came right away. Installation was simple, the hardest part was figuring out I had to pry off the cover at the center of the dial to remove the clip that held the dial onto the pin. Once that was done, it was easy to see which screws had to be taken out,... Read more
Mounting bolt secures the tub and internal components in your laundry center. Replace if stripped, rusted, or missing to restore stable assembly fit.
Purchased and installed new tub bearing and seals. Decided to replace the tub bolts as well, since I had it apart. Now if I could just find a new outer tub (which the manufacturer has discontinued). Appliance parts pros has a great "how to" video which made it simple! Read more
Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.
Screw: 8-16 x 3/8 inch.
Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.
Not one to patch a job, I ordered all seal kit, bearing kit, new shaft keeper, transmission oil, spanner wrench. I have the newer version of the agitator shaft so it does not have the groove for the internal clip. I Custom ground a thick washer so that as the agitator shaft goes into the transmission it fit flush into the slot for the old style shaft clip. With the plastic keeper in position I marked and pull the shaft. I drilled a hole that would be fit tight against the custom washer and used... Read more
Tension spring restores proper movement in washer mechanical assemblies. Replace if parts sag, rattle, or don't return to position. Confirm fit by model.
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more