Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315
Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.
Symptoms of a bad brake assembly include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I first replaced the two drive belts and the motor springs. That didn't fix it although they did need replacing. I then replaced the two bearings and the brake assy. The washer runs like new. If you replace the brake assembly, you should also replace the bearings. It will save a tear down later on. The Maytag repairman wanted $600.00 dollars to do the job. I did it for less than $200.00. Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.
I took the wash basket out of the tub to remove all the sludge and scale that had accumulated over the years. But I did not have a spanner wrench to remove the large nut holding the basket to the center shaft. No problem - I used a hammer and chisel on the ears. But didn't realize it was a LEFT HAND THREAD!! That's when the nut split in two and I had no choice but to purchase another. Long story short, it's back together and the washer doesn't smell anymore. Live and learn... Read more
Fix water leaking onto the floor or uneven tub filling with this upper water injector. Directs inlet water cleanly into the tub. Easy DIY replacement.
An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more
Replaced the unbalanced lever assembly - cost about $14. I spent about as much time trying to find the part locally as it took to get the part from appliance pros; I ordered the part at 11:45 am on a Monday and the part was waiting for me by the time I got home from work on Tuesday - thank you. The parts schematics you provided on your website were very helpful. Read more
This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:
Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more
Washer won't fill properly or overflows? This water level pressure switch senses tub water and signals when to stop filling. Moderate DIY repair.
Since there was no water entering the machine and the machine will not start until the water level is satisfied, I concentrated on the water level switch. I disconnected the power first, then I jumped the normally open contacts on the water level switch, connected the power and the machine became operable. Ordered a water level switch from Appliance Pros, installed and the machine works great. The cost of the part was about $65.00. I was about to buy new washer at Sears for $500.00. Thanks... Read more
This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:
This genuine OEM part is a washer motor. The washer motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. After continuous use, a washer motor can become inoperable. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the motor needs to be replaced. To replace the motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting bolts holding it to the washer. Proceed to pull the old motor out of its place. Make sure to detach the wire harness and any individual wires on the motor. Reinsert the wires into their correct terminals and install the new motor by threading the bolts that secure it. This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand washers.
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more
Clamp Includes 205529 Bolt Kit. It Does *not* include The The Rubber Seal. If Seal Required, Use WP211232
I removed the front cover and saw water a rusted out drum cover clamp. Water gushed out at this point when i operated the machine. I ordered a new clamp and seal from Appliance Parts Pros, which arrived quickly. I wire-brushed the drum and it's cover clean, in the sealing area and installed the new seal and clamp. NOTE do not set the cover down all the way down, or the tub will not "spin". Leave 3/8- 1/2" clearance between the top of the tub and the upper cover. I chose to fix my old... Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.