Lghb2687pi7a Parts

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This replacement chute guides output through the appliance's passageway so it reaches the correct area. Replacing a cracked or warped chute restores smooth, consistent flow and helps prevent blockages, spills, and misdirected dispensing.

• Directs flow through the intended path between components
• Helps maintain alignment and sealing with adjoining parts
• Restores consistent dispensing/throughput when the original is damaged
• Common symptoms: visible cracks, obstructions, misalignment, or output missing the opening

• Disconnect power; turn off water supply if applicable
• Access the chute by removing the relevant cover or panel
• Transfer any reusable gasket/seal or mounting hardware from the old chute
• Seat and align the new chute fully; reassemble and test operation

This Board Assembly is an OEM part for Frigidaire refrigerators. It serves as a crucial component in the electronic system of the fridge, responsible for controlling various functions such as temperature regulation, defrost cycles, and energy efficiency modes.

The degradation of a fridge's board assembly can occur due to electrical surges, wear and tear over time, moisture exposure, or other electronic malfunctions. These can affect the refrigerator's ability to maintain consistent temperatures, potentially leading to food spoilage or increased energy consumption.

Symptoms of a failing board assembly include:

• Inconsistent cooling or temperature fluctuations.
• The fridge or freezer compartment not cooling adequately.
• The display panel is unresponsive or showing error codes.
• The defrost cycle not functioning properly, leading to frost buildup.
• Unusual noises or the fridge cycling on and off more frequently than normal.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This electronic control board manages incoming power and coordinates your appliance's core functions. Replacing a failed board can restore proper operation, responsiveness, and reliable cycling.

• Distributes and regulates power to internal components through onboard relays and circuits
• Interprets inputs from the user interface and sensors to execute programmed functions
• Helps coordinate starting, running, and stopping of key systems
• Common signs of failure: no power, unresponsive controls or display, intermittent shutdowns, cycles that won't start or complete

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use ESD protection; handle the PCB by the edges to prevent static damage
• Photograph or label connectors; transfer one plug at a time to the new board
• Secure the board, confirm all connectors are fully seated, then restore power to test

This door handle bar lets you grip and open the appliance door smoothly. It restores a secure, comfortable handle when the original bar is loose, worn, or damaged, helping the door operate as intended.

• Provides a sturdy handhold to open and close the door
• Replaces a loose, cracked, or missing handle bar
• Helps ensure proper door operation and user safety
• Cosmetic refresh for a worn or scuffed handle area

• Unplug the appliance before servicing
• Use the correct screwdriver/hex driver per your model's fasteners
• Support the door while loosening and tightening handle screws
• Do not overtighten; align and snug evenly to avoid damage

The Fill Tube Kit is an OEM part for Frigidaire refrigerators. It contains the tubes used to direct water from the water supply line into the refrigerator's water dispenser and ice maker. As these tubes can degrade over time due to mineral buildup or cracking, this kit provides a like-new replacement to ensure optimal water flow.

Causes of a bad fill tube include mineral or limescale deposits restricting water flow, cracks or leaks developing from general wear and tear, or accidental damage from installation or maintenance issues.

Symptoms of a bad fill tube are:

• Slow or inconsistent water flow from the dispenser
• Dripping or leaks from the fill tube connection points
• Ice maker not working or producing small or misshapen ice cubes
• Water backing up or overflowing in the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Assembly is an OEM part for Frigidaire refrigerators. It includes the electronic circuit boards, touch pad controls and wiring that allow for operation and monitoring of refrigerator functions and temperatures.

Causes can be short circuits, water damage, power surges over time that degrade electronic components. 

Symptoms of a bad control assembly include:

• Failure of temperature or setting displays
• Inoperable or unresponsive touch controls
• Refrigerator malfunctions like freezing up or not cooling
• Repeated blowing of fuses

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A direct-replacement freezer basket handle that restores a secure grip for lifting and removing the freezer basket. Simple swap that helps make basket removal easier and reduces digging or awkward handling. What it does

• Provides a secure grip point for removing, carrying, and repositioning the freezer basket.
• Replaces a cracked, broken, or missing handle to restore normal basket operation.
• Helps prevent slippage or dropping of the basket when loading or unloading.
• Matches original fit and attachment style for straightforward replacement on compatible units.

• One freezer basket handle.

• Disconnect power and remove stored items from the basket before servicing.
• Most installs require removing the basket to access the handle; basic hand tools may be needed.
• Follow model-specific instructions in the service manual for removal and fastening details.

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This seal-damper is the gasket that fits around a refrigerator's air damper to help keep compartments properly separated and maintain intended airflow. Replacing a torn or compressed seal helps reduce uneven cooling and drafts. What it does:

• Seals the air damper opening to limit unwanted air exchange between compartments
• Helps maintain stable temperatures by preventing cold or warm air leakage
• Common symptom fix: reduces uneven cooling or warm spots near the damper area
• Also helps reduce excess frost or condensation that can form from persistent air leaks

• Disconnect power to the appliance before starting any repair and remove nearby food/shelves for access
• Access the damper housing per your model's service instructions, remove the old seal, and seat the new seal onto the damper frame or mounting groove
• Clean the mounting surface of debris or old adhesive so the new seal sits flat; use gentle pressure to fully engage the seal
• If the damper housing is cracked or the seal does not seat properly, replace the damper assembly.

This LED light board powers the refrigerator's interior lighting, restoring bright, dependable illumination when the lights go dim, flicker, or stop working. It replaces the failed circuit board that drives the factory LED light module. What it does:

• Supplies regulated power to the refrigerator's interior LED light module
• Restores proper illumination in the fresh food and/or freezer sections (varies by model)
• Common symptoms: no interior light, dim light, flickering/strobing, or intermittent lighting
• Direct replacement for the original failed light control board

• 1 LED light board

• Disconnect appliance from power before servicing
• Handle the board by the edges and observe ESD precautions
• Note connector orientation; transfer lens/housing from the original assembly if required
• Ensure connectors are fully seated before restoring power

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This replacement gear restores the transfer of motion inside the refrigerator's mechanism so the assembly operates smoothly and reliably. Designed to match the original fit and drive characteristics for consistent performance.

• Transmits rotation between mating shafts/components within the assembly
• Worn or stripped teeth can cause stalling, slipping, or clicking/grinding noises
• Visual inspection often reveals rounded, cracked, or missing teeth

• Disconnect power before servicing
• Note the original gear's orientation and any timing/alignment marks before removal
• Transfer any clips, spacers, or washers from the original part as needed
• Inspect mating gears/shafts for wear and replace related parts to prevent repeat failure

Replacement water tube that routes water from the inlet valve to the refrigerator dispenser and ice maker, helping restore proper water flow for reliable dispensing and ice production. What it does:

• Carries water from the refrigerator inlet/valve to the dispenser and ice maker fill system.
• Used when cracked, kinked, clogged or brittle tubing prevents water flow.
• Helps stop leaks and restore normal ice maker fill when tubing is damaged.
• Addresses symptoms such as no water at the dispenser, ice maker not filling, or visible leaking under the fridge.

• Turn off the water supply and unplug the refrigerator before beginning any work.
• May require basic hand tools and careful routing to avoid kinks; do not overtighten fittings.
• Inspect and replace any damaged clamps or seals; test for leaks after reconnecting the water supply.

The Handle Mounting Block is an OEM part for Frigidaire refrigerators. It is a component that secures the door handles in place and allows for proper opening and closing functionality. The handle mounting block is designed to provide a sturdy anchoring point for the handles while absorbing potential stresses.

Causes of a bad handle mounting block can include wear and tear over time, cracks or breaks due to overtightening of handles, or physical damage from impacts or mishandling.

Symptoms of a bad handle mounting block include:

• Loose or sagging door handles
• Difficulty opening or closing the refrigerator door
• Handles detaching from the door
• Cracks or breaks visible in the mounting block

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water inlet tube routes water from the inlet valve to the ice maker and dispenser, restoring proper water flow and helping prevent leaks. Use when the original tube is cracked, split, or blocking water delivery. What it does:

• Directs water from the refrigerator inlet valve to the ice maker and dispenser assembly.
• Restores normal water flow if the original tube is crushed, cracked, or blocked.
• Helps stop leaks associated with damaged or deteriorated inlet tubing.
• Common symptoms: no water to ice maker or dispenser, slow dispenser flow, or visible leaking beneath the fridge.

• Disconnect electrical power and shut off the household water supply before starting.
• Handle tubing carefully and avoid sharp bends or kinks when routing.
• Check and reuse or replace any associated fittings, clips, or seals as needed for a secure, leak-free connection.