Lsc27590sw Parts

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This controller assembly is the appliance's main electronic control that manages cycles and user inputs to restore proper control operation. Replace a failing controller assembly to address unresponsive controls, incorrect cycle behavior, or intermittent errors. What it does:

• Manages cycle selection, timing, and communication between sensors and motors to coordinate appliance operation.
• Interprets user inputs from the front panel and sends commands to other components.
• Failure may cause unresponsive buttons, unexpected error codes, stalled or incorrect cycles, or an appliance that won't start.
• Replacing the assembly often resolves control-board–related faults when diagnostics point to the main controller.

• Disconnect power (unplug or switch off breaker) before removing the old assembly to avoid shock or damage.
• Handle the board and connectors carefully; avoid static discharge and cradle the assembly by its edges.
• Match the replacement to the exact part number and transfer any brackets, grounding straps, or button housings as needed.

Refrigerator not dispensing water or making ice without a filter? This bypass cap lets water flow directly to the dispenser and ice maker. Easy install.

Upper hinge assembly for refrigerator doors. Mounts at the top to support and pivot the door. Replace if hinge is worn, cracked, or broken to restore alignment.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This is a compressor start relay assembly that mounts onto the compressor and helps it start up properly. It provides the initial electrical boost needed to get the compressor running and then disengages once the compressor reaches operating speed. Replace this part if the refrigerator is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.

Refrigerator dispenser lever that controls ice and water dispensing through the door. Replace if cracked, broken, loose, or missing for proper function.

Holds the water filter and connects water lines in your refrigerator. Replace if leaking, cracked, or connections are damaged. Verify fit by model number.

Ice not dispensing or grinding noise from dispenser? This auger motor rotates the ice bin auger to move ice cubes through the chute. DIY repair part.

Replacement door stopper assembly that cushions and limits door travel. Installs at the hinge area. Needed when original is cracked, broken, or missing.

Replaces cracked or broken tube connector in your refrigerator. Secures and routes tubing to prevent leaks from loose connections. Easy install.

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.