Lsg7806aa Parts

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

Replaced water level switch, washer fill to proper water level and work fine now. Read more

• Will not drain

I've never fixed a major appliance, so I was quite proud to be able to fix our washing machine. My husband likes to hire repairmen for such issues, but I like to avoid the cost if at all possible. First, I searched online for the cause of the washer not draining. Forums and youtube videos informed me that it was either a faulty pump or clogged hoses. After watching some DIY videos, I removed the front panel which revealed a fairly simple setup inside: a big tub, the motor, and a pump with two... Read more

I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more

I first replaced the two drive belts and the motor springs. That didn't fix it although they did need replacing. I then replaced the two bearings and the brake assy. The washer runs like new. If you replace the brake assembly, you should also replace the bearings. It will save a tear down later on. The Maytag repairman wanted $600.00 dollars to do the job. I did it for less than $200.00. Read more

Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more

I took the wash basket out of the tub to remove all the sludge and scale that had accumulated over the years. But I did not have a spanner wrench to remove the large nut holding the basket to the center shaft. No problem - I used a hammer and chisel on the ears. But didn't realize it was a LEFT HAND THREAD!! That's when the nut split in two and I had no choice but to purchase another. Long story short, it's back together and the washer doesn't smell anymore. Live and learn... Read more

An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more

Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more

Removed shaft with slide hammer and inspected the yoke and gearing replaced the shaft and seals with the shaft kit and replaced the tub bearing. 32 years and still running strong Maytag yeah!!!! Doubt the newer ones will run as long thanks for having the parts. Read more

I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more

This was my first ever self appliance repair. The videos provided by Appliance Parts Pros were excellent and gave me the confidence to do the work myself. My Maytag dryer model opened differently than the one in the videos. I had to remove the front panel and screwing in the paddle required reaching way back and working in a small space where I couldn't see what I was doing. It was uncomfortable but doable with a nut driver and a bit of elbow grease. The part fit perfectly and it looks good as... Read more