Lte612 Parts

This is the rear bulkhead panel located at the back of the dryer drum compartment. It provides structural support for the drum and helps seal the rear of the drying chamber. Replace this part if you notice excessive heat escaping from the back of the dryer, unusual noises during tumbling, or if the panel is visibly cracked or warped.

Secures panels and components to prevent rattling and vibration. Replace when clips break or loosen. Verify fit with your laundry center model number.

Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.

Secures and stabilizes the washer drum assembly. Replace if loose, rattling, or causing excessive vibration during spin cycles. Verify fit with your model.

The Balance Ring is an OEM part for Whirlpool washing machines. This part maintains the stability of the washer drum during the spin cycle. It contains liquid that helps balance the load, minimizing vibrations and noise while ensuring smooth operation.

Causes of a bad balance ring can include general wear and tear, exposure to heavy or unbalanced loads, or physical damage.

Symptoms of a bad balance ring include:

• Excessive shaking or vibrating during the spin cycle
• Loud banging noises
• Washer moving or walking during operation
• Uneven or off-balance loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.

• Holds components on a shaft or within a groove to prevent axial movement
• Maintains alignment of related parts in the assembly
• Common failure signs: ring is bent, missing, or won't stay seated
• Symptoms include loose or wobbly parts and rattling during operation

• Disconnect power before servicing
• Wear eye protection—retaining rings can spring free during removal
• Use appropriate snap-ring pliers or small picks to remove/install
• Ensure the ring is fully seated in the groove before reassembly and use

Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.

Used for the pressure switch.

Color: White.

Encloses the blower wheel and seals the housing for efficient airflow. Replace if cracked, broken, or missing to restore proper air movement.

A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does

• Centers and stabilizes the cam on its shaft for reliable engagement.
• Prevents metal-on-metal wear between the cam and shaft.
• Helps eliminate binding, wobble, or uneven operation caused by a worn sleeve.
• Common symptom of failure: noise, sticking, or irregular movement from the cam-driven mechanism.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the appropriate service panel; follow the model service manual.
• Inspect mating cam and shaft for wear; replace any damaged components.
• Reassemble panels and verify proper operation before returning the appliance to service.

Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.

This push-to-start knob replaces a worn or broken control knob on compatible top-load washers and makes starting cycles simple again with a clean, color-matched finish. Restores tactile control for reliable cycle selection. What it does:

• Replaces a damaged or faded push-to-start knob so you can engage the washer's start function easily.
• Provides a secure grip and clear tactile feedback when pressing to start a cycle.
• Helps resolve symptoms such as a loose, cracked, or non-responsive start knob.
• Matches biscuit (light tan) control panels for a cohesive appearance.

• Disconnect power to the appliance before beginning any repair.
• Most installs are simple push-fit replacements; pull the old knob straight off and press the new knob onto the shaft until it seats.
• If knob removal is difficult, access any retaining clips or fasteners.