Lte624/Aw0 Parts

Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.

Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.

Used for lid switch.

This is a fabric softener dispenser cup that sits inside the washer's agitator or dispenser housing and releases softener at the appropriate time during the rinse cycle. It is typically a small plastic cup or basket designed to hold liquid fabric softener. Replace it if fabric softener is not dispensing properly, the cup is cracked or warped, or you notice softener residue left on clothes.

Rear leveling foot assembly that supports the back of your laundry center. Replace if cracked, broken, worn, or missing to restore stability.

Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins/paddles to lift and move garments so water and detergent reach fabric fibers for better cleaning.
• Promotes even water circulation and load movement to reduce tangling and bunching.
• Common service reasons: cracked or broken fins, missing or worn agitator, noisy operation, excessive vibration, or clothes not coming out clean.
• Designed for top-load agitator-style wash systems that use the PC-144 agitator design.

• Disconnect power (unplug) and turn off water before starting any repairs.
• Typical replacement requires removing the existing agitator cap and any retaining hardware, then sliding the agitator off the drive post and installing the new unit; procedures vary by model—refer to your model's service manual or diagram.
• If a retaining bolt or special fastener is used on your model, have the correct socket or tool ready; follow manufacturer guidance for proper securing.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Size: 10-16 x 5/8 inch.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

Right hand side. For screws use WPW10119828.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Vinyl door seal creates an airtight barrier to maintain proper temperature and prevent energy loss. Replace when worn, cracked, or causing drafts.

Used from harness to top.