Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Lwmt72uv Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

More
Insert, Spline (Spline Insert)
Genuine Whirlpool part
By: Whirlpool
Part Number: WP40008301

This spline insert is the small splined bushing that fits onto a drive shaft to transfer rotational force between the motor/shaft and the driven part. It restores a secure, slip-free connection for proper appliance operation. What it does:

  • Provides a keyed, splined interface between the drive shaft and the driven component to transfer torque
  • Prevents slip or loss of drive that can cause the drum/agitator to stop turning
  • Worn or damaged splines can cause grinding, slipping, or intermittent movement
  • Restoring the insert can eliminate looseness and reduce related noise
What's included: One spline insert Install notes:
  • Disconnect power before servicing; follow all safety precautions
  • Access and removal often require removing the relevant panel or assembly (drum/agitator area)
  • Inspect mating shaft and surrounding components for wear and replace as needed
  • Install with correct orientation and fully seat on the splined shaft; test operation after reassembly

More
Washer Basket To Shaft Gasket
Genuine Whirlpool part
By: Whirlpool
Part Number: WP35-3685

Seals the basket to center shaft, preventing leaks and reducing noise. Replace if leaking between tub and transmission. Confirm fit with your model.

Do-It-Yourself Stories from Customers like You Washer was leaking between outer tub and mounting base plate   Jeffrey T. • Stallings , NC • May 07, 2016

Replaced all seals, unfortunately it is still leaking. I can see where it is leaking from. I am going to tear it back down use some ultra grey gasket maker and reinstall tub gasket. Hoping that works. If it still leaks I will be using the washer as a large paper weight. Read more

More
Washer Water Inlet Mixing Valve
Genuine Whirlpool part
By: Whirlpool
Part Number: 33930

The water inlet mixing valve controls the flow and temperature of water entering the washer by blending hot and cold water supplies. Located at the back of the machine where water lines connect, it responds to temperature selection commands. Replace if water temperature is incorrect, no water enters the tub, or leaking occurs at the valve connections.

More
Knob- Sele
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21001239

 

Do-It-Yourself Stories from Customers like You Plastic knobs broke   Sharon D. • Streamwood , IL • July 28, 2019

Replacement knobs work perfect. Thank you for quick service! Read more

More
Seal- Tub
Genuine Whirlpool part
By: Whirlpool
Part Number: WP35-2328

 

More
Screw, 10 - 16X1.75
Genuine Whirlpool part
By: Whirlpool
Part Number: WP40063701

 

More
Washer Tub Bearing And Seal Housing Assembly
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001561

This assembly supports the wash tub rotation and creates a watertight seal to prevent leaks into the motor area. Located at the bottom rear of the tub, replacement is needed when you hear loud grinding noises during spin cycles or notice water under the washer.

More
Lower Bearing Assembly
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001562

Screws and instruction sheet included.

Do-It-Yourself Stories from Customers like You Bearings were worn out makeing a lot of noise   Lawrence L. • Largo , FL • August 08, 2015

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

More
Knob And Skirt Assembly
Genuine Whirlpool part
By: Whirlpool
Part Number: 12500058

 

More
Plate & Screw Assembly
Genuine Whirlpool part
By: Whirlpool
Part Number: 21001783

 

More
Stabilizer Bar
Genuine Whirlpool part
By: Whirlpool
Part Number: 21001881

 

More
Drain Hose
Genuine Whirlpool part
By: Whirlpool
Part Number: 211704

 

More
Cord Grommet
Genuine Whirlpool part
By: Whirlpool
Part Number: 211881

 

More
Flat Washer
Genuine Whirlpool part
By: Whirlpool
Part Number: 25-7047

 

More
Screw
Genuine Whirlpool part
By: Whirlpool
Part Number: 25-7438

 

More
Drain Pump
Genuine Whirlpool part
By: Whirlpool
Part Number: 27001233

Attaches directly to the motor.

Do-It-Yourself Stories from Customers like You Leaking water from the pump anytime there was water in the washer tub   Alex B. • Stamford , CT • June 30, 2014

My wife found soapy water on the floor of the laundry room. I removed the front access cover on the washer and found water in the bottom of the washer and seeping our the drain holes. Running a rinse and spin cycle showed water leaking out of the pump all the time there was water in the tub. I ordered this pump and after watching a youtube video of someone else doing it had no trouble installing it. Problem fixed. You do need a torx head screw driver T20 or T25 to remove the pump from the motor. Read more

More
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google