Magicchef 31211Xaa Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

• Oven not heating evenly

Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

Part arrived quickly and was an easy install1 Read more

It was very easy to fix after watching your video.. Read more

Took off the old ones and put on the new ones, 123. Read more

Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more

My boyfriend is to do it yourself Mr. Fix-It type remind you that I am also inquisitive when it comes to building and repairing things, but not like him. He is definitely what you call a jack-of-all-trades basically self-trained. Read more

I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more

I ordered and replaced the old ignitor and the corroded mounting screws. Read more