Mav9557eeww Parts

Replaced the lid switch. Everything works fine. Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more

I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more

• Will not fill with water
• No hot or cold water

1.) Made sure BOTH Hot & Cold Water Lines turned off to Maytag Washer. (I have dual shut-off valve for those two water lines), 2.) Briefly ran Washer on Warm Water Setting, removing water pressure & remaining water from Hot & Cold water lines. 3.) Unplugged Washing Machine. 4.) Used Needle Nose Pliers to remove BOTH Hot & Cold Water hoses from the hookup on the back of the washer. 3.) Made sure I had an empty bucket, on hand, to catch remaining water that may come out of now-removed, hot &... Read more

• Shakes and moves

1.) Made sure BOTH Hot & Cold Water Lines turned off to Maytag Washer. (I have dual shut-off valve for those two water lines), 2.) Briefly ran Washer on Warm Water Setting, removing water pressure & remaining water from Hot & Cold water lines. 3.) Unplugged Washing Machine. 4.) Used Needle Nose Pliers to remove BOTH Hot & Cold Water hoses from the hookup on the back of the washer. 3.) Made sure I had an empty bucket, on hand, to catch remaining water that may come out of now-removed, hot &... Read more

The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more

Replaced lid safety switch, actuator and plunger. Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more

• Won't start

Replaced timer in less than 5 minutes along with timer knob. Read more

Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more

Effortlessly Read more