Maytag Ensignia Parts

Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:

• Secures panels, control boards, brackets, and trim to maintain correct assembly
• Replaces stripped, broken, or missing screws that cause loose or rattling parts
• Helps prevent misalignment that can interfere with doors, knobs, or covers
• Standard fastener interface — use the correct driver and size for a secure fit

• Disconnect power and/or gas and follow appliance safety procedures before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damage to threads or surrounding parts
• If threads are damaged, replace the mating component or use the correct thread-repair method

This lid switch housing secures and protects the washer's lid switch assembly so the machine can detect the lid position reliably. It replaces a cracked or broken housing to restore proper switch alignment and protection. What it does:

• Holds the lid switch assembly in the correct position for reliable lid detection.
• Shields the switch from impacts and debris that can cause intermittent failures.
• Common symptom: washer won't start, won't spin, or shows lid-lock-related errors when the housing is damaged.
• Restores consistent electrical/mechanical engagement between the lid and switch when installed correctly.

• Unplug the appliance before beginning any service to avoid shock or injury.
• Basic hand tools are typically needed; follow the OEM diagram for correct removal and reassembly.
• Inspect the lid switch and wiring while replacing the housing; replace any damaged components.

This door hinge supports and pivots the door for smooth opening and secure closing. Replacing a bent or worn hinge restores proper alignment so the door latches consistently and the appliance operates as intended. What it does and when to replace:

• Provides the pivot point between the door and cabinet
• Maintains door alignment with the catch/strike for a tight, reliable close
• Replace if the door sags, rubs, binds, or won't stay closed
• Help resolve no-start issues caused by the door switch not engaging

• 1 door hinge

• Disconnect power; shut off gas supply before servicing
• Support the door while removing/installing hinge screws to prevent strain or damage
• Transfer and reuse original mounting hardware as designed
• After installation, check and adjust latch/door-switch alignment as needed

This gasket seals the basket to the center shaft to help prevent leaks and reduce noise from worn or damaged seals. It restores a proper seal between the tub/basket and the drive shaft for reliable operation. What it does:

• Seals the gap between the basket/tub and the center drive shaft to help prevent water from leaking into the motor/tub area
• Helps reduce rubbing noise caused by a worn or torn seal
• Restores a tight fit after seal failure, wear, or damage
• Common symptom: water leakage from the tub area or visible wear around the shaft opening

• Refer to the exploded parts diagram for correct positioning and orientation
• Inspect mating surfaces for damage or residue and clean before installing the new gasket
• Replace only when the appliance is unplugged and water supply is turned off; follow safety procedures for draining and securing the unit
• If other components show wear (shaft seals, basket, or fasteners), replace them as recommended by the OEM

This 4-position rotary temperature control is the selector switch used to choose basic temperature settings in compatible refrigerators. It restores reliable temperature selection and helps return the appliance to normal cooling behavior. What it does:

• Provides four discrete temperature/setting positions for the refrigerator control circuit
• Sends the selected position signal to the cooling system to adjust running cycles
• Commonly replaced when the temperature dial feels loose, won't change settings, or the fridge doesn't respond to position changes
• Helps diagnose selector-related issues by allowing continuity and position testing

• Disconnect power to the appliance before starting work to prevent shock or injury
• Handle wiring and connectors carefully; note wire locations before removal for correct reinstallation
• Test the switch with a multimeter for continuity through positions

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

A replacement selector knob that fits on the appliance control panel so you can choose cycles or settings with a secure, easy-to-turn control. Restores lost or damaged knobs for reliable panel operation. What it does:

• Fits onto the control shaft to let you change cycles, temperatures or functions
• Replaces a cracked, stripped, or missing selector knob to restore tactile control
• Provides a positive detent feel so selections stay in position during use
• Works with compatible Whirlpool control panels that accept this shaft-mounted knob

• Disconnect power (unplug or shut off breaker) before servicing the control panel
• Pull the old knob straight off the control shaft; push the new knob fully onto the shaft until it seats
• If the control shaft is damaged, replace the underlying control or shaft adapter as needed

Spesc: #12 pozi - drive