Need Help?
Call
Idler pulley wheel installs near the motor to guide and tension the drum belt. Replace if cracked, worn, or bearing has failed after years of use.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
Usually ships within 4 - 14 days
Fix water leaking from detergent dispenser area or inlet connections with this washer injector valve. Acts as siphon break in water supply system.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Washer making noise or controls not stopping correctly? This stop lug limits component movement to prevent over-travel. Simple snap-in repair.
I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more
Fix a loose or slipping agitator that clicks or ratchets during wash cycles. This spring restores proper tension inside the agitator assembly.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
Washer won't spin or spins weakly? A worn clutch plate causes slipping and shuddering during spin cycles. Moderate DIY repair restores reliable performance.
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Replacement bolt for securing panels, brackets, and assemblies in laundry centers. Needed when original fastener is stripped, missing, or damaged.
A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does
Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.
At first i just bought the belt, started dryer and off came the belt, and yes it was in place,looking at the idler arm it had a lot off back and forth movement so i ordered the whole assembly but the spring which no one has.put it all together again but drum barely turned.. so back apart and belt was in place. took the idler spring out cut 4 loops off it re did the end so it would hook on idler arm.and that did the trick.runs like new. Read more
Spesc: #12 pozi - drive
Hex-head screw secures the bearing insert in your washer. Replace if stripped, missing, or damaged to restore proper bearing alignment and retention.
Replaced the drain pump. Read more
Replacement fastener nut for securing panels, brackets, and components in various appliances. Needed when original nut is stripped, missing, or corroded.
This exhaust vent extension restores proper exhaust airflow by lengthening or adapting the appliance exhaust outlet to the vent duct. It helps maintain safe ventilation and reduces backpressure that can cause poor performance or odors. What it does:
Small hex nut secures panels, brackets, and components in dryers and laundry centers. Replace worn, missing, or stripped nuts to restore proper fit.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.