Maytag Msd2351heb Parts

6 - 19 x .250

Rubber grommet that cushions and secures the refrigerator condenser assembly. Replace if cracked, worn, or missing to reduce vibration and noise.

This genuine replacement screw secures panels and components so your appliance stays stable and trim pieces fit properly. It's a simple, exact-fit fastener intended to replace a missing or damaged mounting screw. What it does:

• Fastens panels, trim, control housings or brackets to the appliance frame
• Restores secure fit when a screw is missing, stripped, or corroded
• Helps eliminate rattling or loose panels caused by a missing fastener
• Matches OEM thread and head style for correct seating and torque

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until parts are firmly seated
• Disconnect power and follow appliance safety guidelines before servicing

This clamp secures flexible hoses to fittings to maintain a tight seal and prevent leaks. Use it to replace a worn or loose clamp to stop water or air seepage and restore proper hose attachment. What it does:

• Holds a washer, dryer, or appliance hose firmly to a barb or fitting to prevent slipping
• Helps maintain a watertight or airtight connection to reduce leaks and drips
• Replaces corroded, cracked, or stretched clamps that no longer grip reliably
• Supports normal appliance operation by keeping fluid/air flow contained

• One clamp

• Inspect the hose and fitting; replace the hose if damaged before installing the clamp
• Position clamp over the hose barb and tighten evenly; avoid over-tightening that can cut the hose
• Disconnect power and water supply before servicing any appliance components

Size: 8-32 x 1/4 inch.

Size: 8-32 x .312 inch.

Replacement power cord for refrigerators. Restores electrical connection when the original cord is frayed, damaged, cracked, or has broken prongs.

Ice dispenser not working or ice won't dispense? This auger motor drives the ice dispenser mechanism. Most DIYers complete this repair in 15-20 minutes.

This wire harness connects key internal components so power and signals are routed correctly. Replace a damaged harness to restore reliable operation when the original wiring is burned, brittle, cut, or causing intermittent electrical connection issues.

• Carries electrical power and control signals between designated components
• Restores dependable connections when wires or terminals are heat-damaged, broken, or corroded
• Helps address no-operation or intermittent operation of the affected component(s)
• Common clues include scorched insulation, loose/burned connectors, or visible wire damage

• Disconnect power before servicing; shut off gas/water if applicable
• Photograph/label connections and routing before removal
• Route and secure wiring exactly as original, away from sharp edges, hot surfaces, and moving parts; reuse existing clips/ties
• Seat connectors fully and avoid pulling on wires during removal/installation

Color: black. Measures about 8-1/2 inches wide by 4 inches deep.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

Black plastic shim that supports and aligns the door hinge assembly. Replace if broken, cracked, or missing to restore proper door alignment.