Maytag Neptune Parts

This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.

• Encloses and supports the blower wheel while channeling air from the drum to the exhaust
• Maintains correct airflow and back pressure for efficient drying performance
• Replace if the housing is cracked, warped, melted, or otherwise damaged
• Typical symptoms include weak vent airflow, longer dry times, rattling or scraping from the blower area, or visible lint leakage

• Disconnect power; if gas, also shut off the gas supply
• Access the blower area by removing the lower/front panel and lint ducting as required by your model
• Transfer the blower wheel and any brackets from the old housing; clean lint from ducts before reassembly
• Ensure the housing seats fully and all duct connections are tight; spin the blower by hand to verify clearance before restoring power

This door boot seal is the flexible gasket that surrounds the front-load washer's door opening. It restores a watertight seal to stop leaks when the original becomes torn, warped, or no longer seats correctly.

• Creates a watertight barrier between the door opening and outer tub
• Prevents water from escaping the front panel during wash and spin
• Helps cushion the door/tub interface to reduce rubbing and wear
• Common symptoms: water leaking at the front, visible tears/cracks, loose or misshapen gasket lip

• Disconnect power and turn off water before servicing
• Remove the outer retaining clamp, peel the old boot from the front panel, then remove the inner clamp from the tub
• Note orientation marks and any hose connections; transfer and seat the new boot evenly
• Reinstall inner and outer clamps securely and verify an even seal before test cycling

The Dryer Timer Dial Skirt is an OEM part designed specifically for Whirlpool dryers. It acts as a protective and decorative cover around the timer dial, providing clear labeling for various dryer settings. 

Color: Bisque

Over time, the dial skirt may degrade due to frequent use, exposure to heat, and potential impact, leading to cracks, discoloration, or broken markings. These issues can make selecting the appropriate cycle difficult or confusing.

Signs that the Dryer Timer Dial Skirt may need replacing include:

• Faded or illegible cycle markings
• Cracks or broken sections on the skirt
• The dial skirt no longer fitting snugly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

To order indicator lens use WP22001948.

This is a control panel used in many dryers. It is an essential part that includes the touchpad for the appliance. This component sits on top of the dryer and allows the user to operate the machine. It includes buttons for cycles, drying temp, and other options for drying clothing after the use of a washing machine. It's made of durable materials but can be damaged and require replacement. It may also malfunction and stop showing cycle information on the front of the panel. The buttons can also experience issues necessitating replacement. If the control panel is damaged or malfunctioning, the first step to take is making sure the dryer is turned off. This will prevent any injuries or damage from occurring during the replacement process. A set of basic tools and a pair of work gloves will also be useful. The original control panel should be carefully removed from the washer and set to the side.This control panel is sold as a single part. It is an OEM replacement component that is sourced directly from the manufacturer. This part is made for use with several Maytag dryers.

Size: 10-32 inch.

This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.

• Fastens the hinge securely to the door or front panel
• Helps maintain proper door alignment to prevent rubbing or sagging
• Replaces missing, stripped, or corroded hardware
• Typical symptoms include a loose/sagging door, difficulty latching, or rattling at the hinge area

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Support the door while removing and installing hinge screws
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace them together for consistent alignment

This is the hot water inlet valve for compatible laundry appliances. It controls the flow of hot water into the machine during fill cycles, helping ensure proper washing performance and accurate temperature mixing.

• Opens and closes to allow hot water into the tub when energized
• A failed valve can cause no hot fill, slow filling, incorrect water temperature, or leaks from the valve body
• Also lead to error codes related to water fill or extended fill times

• Disconnect power and turn off both water supplies before servicing
• Have a towel/contained pan ready for residual water in hoses
• Note hose orientation and electrical connector position before removal
• Inspect and replace inlet screen washers or hoses if restricted or worn

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This clip is a small retaining fastener used to secure components inside your appliance, keeping parts aligned and in place during operation. Replacing a worn or missing clip helps stop looseness, vibration, and premature wear.

• Holds a designated part firmly to its mating surface
• Maintains proper alignment to reduce rattling and shifting during cycles
• Symptoms of failure: parts that won't stay attached, misalignment, buzzing/rattling noises, or a visibly bent/missing clip
• Restores a secure, factory-style fit

• Disconnect power; turn off water supply before servicing
• Note the original clip position and orientation (a quick photo helps)
• Use needle-nose pliers to release/install; avoid over-bending the clip
• Ensure the component is fully seated and secure before reassembly and testing

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

This bracket strike secures the door latch strike to the appliance frame, restoring reliable door closing and sealing. Replacing a damaged or bent bracket helps prevent doors from popping open or failing to latch properly. What it does:

• Secures the door strike so the latch can engage and hold the door closed.
• Restores correct door alignment when a worn or broken bracket causes improper latching.
• Addresses symptoms such as a door that won't latch, pops open, or sits unevenly.
• Provides a direct-fit structural replacement for the original mounting point.

• Disconnect power (and water, if applicable) before beginning any service.
• Access the bracket by removing the door trim or inner panel as required; keep original fasteners.
• Align the strike with the latch, secure with appropriate screws, and test door operation before reassembly.

This drain hose carries used water away from your appliance during the drain cycle. Replacing a worn or damaged hose helps stop leaks and restores proper draining performance.

• Routes wastewater from the appliance's drain system to the household drain
• Replaces hoses that are cracked, brittle, clogged, or kinked and leaking
• Can help when cycles end with standing water or slow/failed draining
• Helps reduce odors and backflow when installed and routed correctly

• Disconnect power and water supply; allow the appliance to cool before servicing
• Move the unit for access; keep towels or a pan handy to catch residual water
• Transfer and tighten existing clamps/fittings to the new hose; route without kinks and secure per your model's instructions
• Run a short test cycle and check all connections for leaks

This cold water inlet valve is the solenoid-operated valve that opens to let cold water into your washer during fill and closes to stop flow. Replacing it restores proper fill speed and helps prevent off-cycle drips.

• Regulates cold-side water flow into the washer during fill and rinse cycles
• Opens when energized by the control; closes to stop water between cycles
• Common signs of failure: no cold fill, slow fill, or dripping into the tub
• May trigger fill/temperature errors or cause a loud hum with little/no water flow

• Disconnect power and shut off the household water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Label and transfer hoses and wire connectors one-for-one to the new valve
• Inspect/clean inlet screens and flush lines; check for leaks after a test fill

This assembly is the housing the dispenser drawer slides into, restoring a smooth pull-out action and proper dispensing. It supports the drawer and channels water through the detergent, bleach, and fabric softener compartments into the tub.

• Holds and guides the pull-out dispenser drawer
• Routes incoming water through the dispenser cups into the washer
• Helps seal the dispenser opening to minimize drips and leaks
• Common symptoms: leaks at the dispenser, poor detergent/softener dispensing, or a drawer that sticks, jams, or won't seat

• Disconnect power and shut off water before servicing
• Remove the dispenser drawer; remove top/console panels as needed for access
• Detach fill hose(s) and outlet chute; transfer any seals, clips, and fittings to the new housing
• Reassemble and run a short fill/rinse to check for leaks

Screw: 8-16 x 3/8 inch.