We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.
The foam was shot on the detergent cup lid. Hard as a rock. Causing caking problems, dribble down the inside wall of the door and leaving lumps of detergent. Cut the door in half wit aviation snips and pulled out the two halves. Discovered at this point that the spring had gone soft. Bought one ahead of time, so I was set. Put the spring on the left pin, put the spring pin in the door, slipped the door into place (open) and put the right pin in with pliers. Door snaps open now. Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Fix continuous water flow or won't-stop-filling issues with this washer hot water inlet valve. Controls hot water during fill cycles. DIY-friendly, 30-minute repair.
After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more
This is a small metal or plastic hinge pin that secures the detergent dispenser door on the dishwasher's inner door panel. It allows the dispenser cover to pivot open during the wash cycle to release detergent. Replace this pin if the dispenser door falls off, won't stay closed, or fails to open properly during a cycle.
This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.
Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more
Secures the door latch strike to the dryer frame for reliable closing. Replace if your bracket is bent, damaged, or missing to restore proper alignment.
Fix washer that won't fill, shows OE/NF error, or keeps running water even when off. Cold water inlet valve replacement takes 5-10 minutes with basic tools.
Screw: 8-16 x 3/8 inch.
Rubber gasket that seals the joint between the tub and cover to prevent leaks and water seepage. Replace if you notice leaking or debris buildup. Verify fit.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Replacement drain hose for washers. Routes wastewater from the drain pump to your household drain. Replace if cracked, leaking, clogged, or worn.
It was a nice match thnx alot Read more
Note: This part is one screw, order quantity needed.
The door hinges on my Maytag Neptune stacked washer/dryer where corroded badly. Took the time to replace the two hinges and repairing the epoxy coating on the front panel of the machine. Unit looks like new. Read more
Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.
Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more
Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.
I pulled out the old housing and unplugged the motor. It pretty much came out in pieces. Remove the plastic from the motor, then had to take a pair of vice grips to hold the spindle in place to remove the auger. Remove what was still attached to the old Housing. Cleaned everything up and put the whole unit back together. The motor looked like it was somewhat cooked but still worked, so I ordered a new motor and auger to replace it. Because this fridge is 24 yrs old, Appliancepartspros... Read more
Specs: No.8-18AB WAFER HD
Size: 10-24 x 3/8 inch.
Replaced timer control unit, first time doing this. Read more
Fix a washer that won't spin or agitate with clicking sounds. This motor control assembly regulates drive motor speed and direction. Moderate DIY repair.
Replaced the motor control assembly. Read more