We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.
I took the wash basket out of the tub to remove all the sludge and scale that had accumulated over the years. But I did not have a spanner wrench to remove the large nut holding the basket to the center shaft. No problem - I used a hammer and chisel on the ears. But didn't realize it was a LEFT HAND THREAD!! That's when the nut split in two and I had no choice but to purchase another. Long story short, it's back together and the washer doesn't smell anymore. Live and learn... Read more
Specs: 10 - 16 x .375
Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more
Dryer not heating? This heater relay controls power to the heating element. Quick DIY fix when cycles stay cold. Includes testing instructions.
Replaced bulb Read more
Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:
I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more
This small hardware washer serves as a spacer/bearing surface within appliance assemblies to distribute load and maintain proper clearance. Replacing a worn washer helps restore smooth operation and alignment of the affected control or mechanism. What it does:
This was my first ever self appliance repair. The videos provided by Appliance Parts Pros were excellent and gave me the confidence to do the work myself. My Maytag dryer model opened differently than the one in the videos. I had to remove the front panel and screwing in the paddle required reaching way back and working in a small space where I couldn't see what I was doing. It was uncomfortable but doable with a nut driver and a bit of elbow grease. The part fit perfectly and it looks good as... Read more
Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more
This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.
Purchased timer and baffle, and my appliance repairman installed them. I could get the parts cheaper than he could from his supplier; he asked me for the Appliance Parts Pros website address! Read more
I had to replace the terminal block due to the 220 volt ark. A small fire at the bottom of the dryer caused the belt to partially burn. I had to replace it along with the 220 volt dryer cable. If the local hardware store would have taken the time to install the dryer with an additional 0.50 cent grommet, this could have been avoided. Thank you for sending the correct parts. This was the second time I had to use your service and I will continue to use it in the future. Read more
Perfectly! Replacing Agitator Shaft is not for the faint of heart. Replacing output shaft pinion gear on the bottom of the agitator shaft requires care, experience and patience with pressing/driving drift pins without damaging the gear itself. One slip of the drift/punch or press apparatus will ruin the gear/teeth face and will lead to failure of the transmission internally when put back into service. As best as I can tell the pinion gear is discontinued and no longer available so take care!... Read more
First I was surprised the switch arrived next day after ordering it. Kudos to AppliancePartsPros for extra fast service. I removed the screws on bottom of front panel to remove the panel. This revealed the inside of the washer. The switch was in upper left corner. The two screws were 1/4 inch hex nut type and were hard to get a ratchet in there. (had to use a ratchet wrench because I dont have an open end wrench.) So it took a while to unscrew the screws. But I was able to remove them. Once... Read more
Clamp Includes 205529 Bolt Kit. It Does *not* include The The Rubber Seal. If Seal Required, Use WP211232
I removed the front cover and saw water a rusted out drum cover clamp. Water gushed out at this point when i operated the machine. I ordered a new clamp and seal from Appliance Parts Pros, which arrived quickly. I wire-brushed the drum and it's cover clean, in the sealing area and installed the new seal and clamp. NOTE do not set the cover down all the way down, or the tub will not "spin". Leave 3/8- 1/2" clearance between the top of the tub and the upper cover. I chose to fix my old... Read more