Mdb7960awq Parts

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

The Sump is an OEM part for Whirlpool dishwashers. It houses the dishwasher's motor and pump assembly, responsible for circulating water and ensuring effective cleaning of your dishes.

A bad sump can occur due to wear and tear, clogs, or damage caused by foreign objects. If you notice issues such as water not draining properly, leaks, or unusual noises during the dishwasher cycle, it may indicate a problem with the sump.

Symptoms of a bad sump include:

• Water not draining or draining slowly from the dishwasher
• Leaks or water pooling at the bottom of the dishwasher
• Unusual noises such as grinding or rattling sounds

Replace your faulty sump with this genuine OEM part to restore your dishwasher. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Dishwasher Filter Screen is an OEM part for Whirlpool dishwashers. As a key filtration component, the filter screen traps food particles and debris to prevent clogs and ensure optimal water circulation during wash cycles. It is responsible for filtering out contaminants and protecting internal pump components from damage.

Symptoms of a bad filter screen include:

• Reduced or uneven water pressure during wash cycles  
• Puddles or pooled water inside the dishwasher
• Food debris caught in the pump or other areas  
• The dishwasher fails to fill or drain properly
• Unusual noises emanating from the dishwasher

Causes of a bad filter screen can include clogging over time due to accumulated food waste and mineral deposits or damage such as cracks or tears in the screen material.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This replacement screw secures appliance panels, brackets, and internal components. Install it when original hardware is missing, stripped, or corroded to restore a solid, factory hold and help stop vibration, rattles, and misalignment.

• Provides secure attachment for covers, brackets, and assemblies
• Replaces missing, damaged, or rusted hardware
• Helps resolve loose panels, buzzing/rattling noises, or shifting parts
• Supports proper alignment and reliable operation when tightened correctly

• Disconnect power; shut off gas/water if applicable before service
• Match thread and length to the original; replace in the same location
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If washers, spacers, or threadlocker were present originally, transfer or replace them

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool dishwashers. It secures the sliding dishwasher rack at the rear of the tub.

Symptoms of a faulty stop clip include:

• Dishes shifting position or toppling during cycles of motion  
• Noisy clattering heard from partially-restricted rack movement
• The dishrack failing to fully retract or extend 

Over time, repeated force from dish impacts can bend the thin metal clip out of place. Fatigue causes it to lose retaining strength.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

The Panel Toe is an OEM part compatible with GE dishwashers. It is a discreet metallic strip located along the bottom front panel of the appliance. The toe provides protection and reinforcement to this high-impact area.   

Causes of a bad panel toe include normal wear from opening and closing the dishwasher door hundreds of times each year. Misalignment from door impact can also cause premature deterioration.

Symptoms of a bad panel toe include: 

• Visible cracking, bending, or detachment of the toe strip
• Potential for other panel issues if toe integrity is compromised
• Possible denting or distortion of neighboring surfaces
• Aesthetic issues and reduced protection of front panel edges

This genuine GE replacement part restores the structure and helps prevent further damage. Compatible Dishwasher models also include some Hotpoint, Profile, and Kenmore units.
 

The Retainer is an OEM part for Whirlpool dishwashers. It securely holds the top spray arm in place underneath the dishwasher interior roof panel.

Causes of a bad retainer include cracking, breaking or deforming from repeated use and natural wear over time.

Symptoms of a bad top spray arm retainer are:

• Loosening or detachment of the upper spray arm during washing cycles
• Reduced or uneven water coverage for upper rack dishes
• Potential rattling or noise from an unsecured spray arm

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement capacitor stores and releases energy to give an AC motor the phase shift it needs to start and run smoothly. Installing a fresh capacitor can help when a motor hums, struggles to start, or cycles off. What it does

• Provides the phase shift/starting torque an AC motor needs and stabilizes operation
• Helps reduce repeated start attempts and nuisance thermal trips
• Common symptoms of a weak capacitor: motor hums, won't start, or stops shortly after starting
• Physical signs of failure can include a swollen, leaking, or cracked casing

• 1 capacitor

• Disconnect power to the appliance before servicing
• Safely discharge the capacitor with an appropriate resistor/discharge tool before handling
• Mark/photograph wire locations and transfer connections one-for-one to the new part
• Reinstall in the original bracket or mounting location; keep wiring secure and clear of moving parts

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This dishwasher sump and seal forms the watertight basin at the bottom of the tub and seats the wash and drain pumps. Replace a cracked sump or worn seal to stop leaks and restore reliable wash performance. What it does:

• Collects and channels wash water to the circulation and drain pumps
• Maintains a watertight seal between the tub and the sump opening
• Helps maintain proper wash pressure and flow
• Common failure signs: water leaking from the base, visible cracks or warping, recurring moisture beneath the unit, poor cleaning results

• One sump assembly with seal

• Disconnect power and shut off the water supply before servicing; use towels to catch residual water
• Remove the toe panel and slide the dishwasher out for access to the sump area
• Detach hoses/wiring as needed; release locking tabs and lift out the old sump
• Seat the new seal evenly, transfer any reusable hardware/components from the original sump, and test for leaks after reassembly

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This factory screw secures components in your appliance to keep them properly mounted and stable during operation. Replacing a missing or damaged screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Fastens panels, brackets, or trim to maintain correct alignment
• Can address rattling, vibration, or loose/misaligned parts where this screw is used
• Helps prevent wear from movement caused by missing or stripped hardware

• Unplug power and shut off utilities before service
• Note original screw location and orientation; replace like-for-like
• Do not overtighten—start by hand to avoid cross-threading
• Address threads before installing the new screw

The Insulation is an OEM part for GE dishwashers. It is located inside the dishwasher tub and helps maintain optimal temperatures during the wash cycle. The insulation forms a barrier that minimizes heat transfer between the tub interior and exterior cabinet walls.  

Causes of bad insulation can include cracks or compression damage over time. Excess moisture during washing may also cause premature breakdown.

Symptoms of a bad insulation include:

• Inability to efficiently heat or maintain water temperatures  
• Extended cycle times and higher energy usage
• Temperature fluctuation issues can trigger error codes
• Condensation or moisture inside the cabinet walls

This genuine OEM GE insulation restores the tub's optimal thermal properties. It is also compatible with some Hotpoint, Profile, and select Kenmore models manufactured for Sears. Replace yours now to optimize energy efficiency and washing performance.