Mdbh965 Parts

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Attaches to the inner tub for the upper rack

This wash arm cap secures the dishwasher spray arm to its hub so it spins freely and distributes water. Replace a worn or missing cap to restore wash performance and keep the spray arm from loosening or coming off.

• Locks the spray arm onto its post/hub for proper alignment
• Allows smooth rotation for even water spray coverage
• Helps prevent wobbling, noise, or the arm detaching during cycles
• Common signs: spray arm falls off, is loose, doesn't spin, or dishes aren't getting clean

• Disconnect power; open the door and remove the rack to access the spray arm
• Unscrew and remove the old cap; lift off the spray arm if needed
• Seat the spray arm and hand-thread the new cap; tighten snugly without over-tightening
• Spin the spray arm by hand to ensure free movement before running a cycle

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

Color: light blue. This tine latch measures about an inch wide.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

This little door seal goes on the corner of the dishwasher door. There are two of these seals - one in each corner. It is recommended to order and replace both. If you need pushnuts, order 99002756.

Color: light blue. Measures about 3/4 of an inch high by 5-1/2 inches deep.

Includes 2 white tines, 2 blue clips, and 1 white clip. The parts in this kit range from about 4 to 10 inches.

This top wash arm retainer secures the dishwasher's upper spray arm so it spins freely and stays aligned, helping maintain proper water distribution for upper-rack cleaning. Replace a cracked or worn retainer to reduce wobble and misalignment. What it does:

• Holds the upper/ top spray arm in place on the spray assembly so the arm can rotate correctly.
• Prevents the spray arm from slipping or wobbling during the wash cycle.
• Helps restore proper water spray coverage to the upper rack when the original retainer is broken or worn.
• Compatible with standard upper spray arm mounting—no modification required.

• Includes: 1 top wash arm retainer

• Disconnect power to the appliance before beginning any repair.
• You may need to remove the upper rack and/or the spray arm to access the retainer; keep parts organized for reassembly.
• Inspect the spray arm and attachment for damage or debris while replacing the retainer.
• Use hand tools only.

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

Specs: No.8X1/2 HEX WASHER HEAD