Mdbh985aws Parts

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

Attaches to the inner tub for the upper rack

This wash arm cap secures the dishwasher spray arm to its hub so it spins freely and distributes water. Replace a worn or missing cap to restore wash performance and keep the spray arm from loosening or coming off.

• Locks the spray arm onto its post/hub for proper alignment
• Allows smooth rotation for even water spray coverage
• Helps prevent wobbling, noise, or the arm detaching during cycles
• Common signs: spray arm falls off, is loose, doesn't spin, or dishes aren't getting clean

• Disconnect power; open the door and remove the rack to access the spray arm
• Unscrew and remove the old cap; lift off the spray arm if needed
• Seat the spray arm and hand-thread the new cap; tighten snugly without over-tightening
• Spin the spray arm by hand to ensure free movement before running a cycle

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

This Tub Edge Trim (bottom) fits along the lower edge of the dishwasher tub opening. Replacing a cracked, warped, or missing trim restores a clean finished edge and helps the door open and close smoothly without rubbing or snagging.

• Finishes and protects the bottom lip of the tub opening
• Helps maintain proper clearance for the door panel and gasket
• Replaces damaged, warped, discolored, or missing trim
• Typical symptoms: loose or broken strip, rubbing when closing, visible gap along the lower edge

• Disconnect power to the dishwasher before servicing
• Open the door and remove the old trim by releasing its retaining tabs or screws; note orientation
• Align the new trim on the lower tub edge and press or fasten until fully seated across the opening
• Verify the door closes freely and the gasket seats evenly before restoring power

This top wash arm retainer secures the dishwasher's upper spray arm so it spins freely and stays aligned, helping maintain proper water distribution for upper-rack cleaning. Replace a cracked or worn retainer to reduce wobble and misalignment. What it does:

• Holds the upper/ top spray arm in place on the spray assembly so the arm can rotate correctly.
• Prevents the spray arm from slipping or wobbling during the wash cycle.
• Helps restore proper water spray coverage to the upper rack when the original retainer is broken or worn.
• Compatible with standard upper spray arm mounting—no modification required.

• Includes: 1 top wash arm retainer

• Disconnect power to the appliance before beginning any repair.
• You may need to remove the upper rack and/or the spray arm to access the retainer; keep parts organized for reassembly.
• Inspect the spray arm and attachment for damage or debris while replacing the retainer.
• Use hand tools only.

Specs: No.8X1/2 HEX WASHER HEAD

Replacement rinse aid dispenser knob restores a simple, reliable way to set and dispense rinse aid in the dishwasher. It gives a clear tactile control for adjusting rinse aid release so dishes dry and rinse with fewer spots. What it does:

• Replaces a cracked, stripped, missing, or hard-to-turn rinse aid control knob
• Allows you to set the dispenser level or open/close the rinse aid dosing mechanism
• Helps resolve problems where the knob won't turn or is detached from the dispenser
• Matches the original dispenser interface for correct fit and operation

• Always disconnect power to the appliance before servicing (unplug or switch off the breaker)
• Access the rinse aid dispenser per the dishwasher service manual or OEM instructions
• Align the knob on the dispenser post and press/snap it into place; avoid forcing or overtightening

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

The Cabinet Mount Bracket secures a built-in appliance to the surrounding cabinetry. Replacing a bent or missing bracket restores a tight, rattle-free installation so the unit stays level and aligned during everyday use.

• Anchors the appliance to the cabinet or side walls to prevent shifting or tip-out
• Maintains flush, level alignment with adjacent cabinets and countertop
• Helps reduce vibration and rattling noises during operation
• Replace if the original bracket is bent, cracked, corroded, or missing

• Disconnect power and any utilities before starting work.
• Support the appliance and pull it forward enough to access the mounting area.
• Reuse manufacturer-specified screws or approved replacements; tighten securely without overtightening.
• Secure both sides as originally configured and test operation.

This left corner trim restores the finished edge on a refrigerator door or cabinet frame, improving appearance and helping protect the gasket area from damage. It's a direct-fit plastic trim piece used where the door meets the cabinet. What it does:

• Covers and protects the door/frame corner to prevent chipping and wear
• Helps maintain a smooth seal surface by securing the gasket edge
• Reduces visible gaps or rough edges that cause cosmetic issues
• Commonly replaced when cracked, broken, or missing after impact or wear

• One left corner trim piece

• Unplug the appliance or disconnect power before beginning work when applicable
• Remove any adjacent trim or fasteners gently to access the mounting area
• Align the trim with the corner and press or fasten per the OEM attachment points
• Avoid forcing the piece; inspect surrounding gasket and mounting clips and replace if damaged

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.