Mdbh989aws Parts

12 Ft in length

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

To order seal use WP8268340.

This Drain Pump Motor Assembly replaces the washer's drain pump motor and impeller so the machine can move water out during drain and spin cycles. Restores proper draining and reduces standing water in the tub. What it does:

• Pumps water from the tub during drain and spin cycles to help clear wash water.
• Replaces a failed or noisy pump motor that hums but won't drain.
• Stops or reduces standing water and slow-drain symptoms.
• Helps address leaks or visible damage at the pump housing or impeller.

• Disconnect power and turn off water supply before starting any repair.
• Remove the washer access panel and drain remaining water from the tub before replacing the pump.
• Note wiring and hose locations during removal; reconnect hoses and electrical plug securely.

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

This tube nut secures the water inlet tubing to its fitting, creating a tight, leak-resistant connection. Use it when the original nut is cracked, stripped, or can no longer hold the line securely.

• Tightens over the inlet fitting to clamp the water tube and form a reliable seal
• Helps stop drips at the water-line connection point
• Addresses loose or damaged inlet connections and difficulty keeping the tube seated
• Commonly replaced when the nut is worn, cross-threaded, or visibly cracked

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Hold the fitting with one wrench while tightening the nut with another to avoid twisting components
• Do not overtighten; restore water and check for leaks after installation
• Inspect the tubing, ferrule/sleeve, and insert; replace if worn or damaged

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint