Mde66byw Parts

Specs: No.8-18AB WAFER HD

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Specs: 7/32 INCH

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This door hinge supports and pivots the door for smooth opening and secure closing. Replacing a bent or worn hinge restores proper alignment so the door latches consistently and the appliance operates as intended. What it does and when to replace:

• Provides the pivot point between the door and cabinet
• Maintains door alignment with the catch/strike for a tight, reliable close
• Replace if the door sags, rubs, binds, or won't stay closed
• Help resolve no-start issues caused by the door switch not engaging

• 1 door hinge

• Disconnect power; shut off gas supply before servicing
• Support the door while removing/installing hinge screws to prevent strain or damage
• Transfer and reuse original mounting hardware as designed
• After installation, check and adjust latch/door-switch alignment as needed

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

This is a genuine replacement mounting screw used to secure appliance components and panels. It restores proper fit and prevents movement that can cause noise or misalignment. What it does:

• Fastens panels, brackets, and small components in place
• Helps stop rattling or vibration caused by loose hardware
• Restores secure attachment after stripped or missing fasteners
• Matches OEM thread and head style for correct fit

• Use the correct driver to avoid stripping the head
• Tighten until snug; do not overtighten to prevent damage
• Disconnect power to the appliance before accessing internal components
• Replace matching screws in the area for consistent fit

This terminal block provides the electrical connection point between the washer's power cord and the appliance wiring, restoring a secure, stable supply for safe operation. It replaces a damaged or corroded connection assembly. What it does

• Secures and insulates power cord wires where they enter the washer to prevent loose connections and arcing
• Restores reliable incoming power when a burned, loose, or broken terminal causes intermittent power or no power
• Helps prevent electrical resistance and heat buildup at the cord connection
• Matches OEM mounting and terminal layout for a direct replacement

• One terminal block assembly as shown

• Disconnect the washer from power before servicing to avoid shock or injury
• Inspect wire colors and terminal positions, then transfer wires to the same terminals on the replacement part
• Typical installation requires basic hand tools (screwdriver, nut driver); some models may need partial cabinet access
• If you see melted insulation or other wiring damage, replace affected wiring.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:

• Provides the appliance's main AC power connection so it can operate
• Replaces frayed, cut, or otherwise damaged cords to eliminate power loss
• Can resolve symptoms like no power, intermittent power, or visible cord damage
• Designed for direct replacement where the OEM cord mounts and terminates the same way

• Unplug the appliance or disconnect power at the breaker before servicing
• Route the cord and attach with the existing strain relief or mounting bracket
• Ensure connections match the original cord terminals and are tight

This is a replacement mounting screw used to secure panels, brackets, and internal components on compatible appliances, restoring proper fit and reducing rattles or loose parts. What it does:

• Secures panels, trim, brackets, or internal assemblies
• Stops rattling or vibration caused by missing or loose fasteners
• Replaces a lost or stripped screw to restore proper alignment
• Works as a direct-fit hardware fastener when the OEM screw is damaged or missing

• Turn off and unplug the appliance before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid cracking plastic or stripping threads

This terminal block connects the appliance to household power, providing a secure point for the incoming power cord wires. Replacing a damaged terminal block restores a solid electrical connection and reduces fire risk. What it does:

• Secures and organizes incoming power cord wires to the appliance's internal wiring
• Provides stable electrical contact for consistent power delivery
• Prevents loose or arcing connections that can cause intermittent power or overheating
• Common symptoms: appliance won't power on, intermittent power loss, visible burning or melted plastic at the power entry point

• Disconnect power at the breaker and verify the appliance is de-energized before starting
• Confirm wire placement and tightness; replace any scorched or damaged wiring or connectors
• Use proper tools and follow the appliance wiring diagram; tighten terminal screws to manufacturer torque if specified

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This 4-position rotary temperature control is the selector switch used to choose basic temperature settings in compatible refrigerators. It restores reliable temperature selection and helps return the appliance to normal cooling behavior. What it does:

• Provides four discrete temperature/setting positions for the refrigerator control circuit
• Sends the selected position signal to the cooling system to adjust running cycles
• Commonly replaced when the temperature dial feels loose, won't change settings, or the fridge doesn't respond to position changes
• Helps diagnose selector-related issues by allowing continuity and position testing

• Disconnect power to the appliance before starting work to prevent shock or injury
• Handle wiring and connectors carefully; note wire locations before removal for correct reinstallation
• Test the switch with a multimeter for continuity through positions

Spesc: #12 pozi - drive