We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures panels, brackets, and internal components in your range. Replace stripped, missing, or damaged screws to keep parts properly aligned and secured.
Unscrewed and removed broken parts, and replaced with new parts, takes about 15-30 mins to do all 4 tubes. Read more
This retaining ring secures a component in its groove on a shaft or housing, keeping parts aligned and in place during operation. Replace a bent, stretched, or missing ring to restore a tight hold and reduce movement or noise.
Replaced pin Read more
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more
Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.
Ordered new part. watched repair instructions on UTube. repair went well. Struggled with the grommet that holds the wiring harness. Didn't see that another grommet comes with the switch and wiring harness. Read more
Screw: 8-16 x 3/8 inch.
Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.
Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more
Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.
Pulled off old knob and pushed on new knob. That easy. Read more
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.
This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.
Dryer won't heat or start? A faulty gas valve assembly that controls gas flow to the burner is often the cause. Direct-fit part for gas dryers.
If your dryer won't advance through cycles or gets stuck mid-cycle, the timer control likely needs replacement. This part restores automatic cycle sequencing.
Replaced with new timer Read more
Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.
Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.
I submitted my question, and problem to Appliances Pro, and they informed me that the problem was with my gas valve, or gas safety value. Read more