Mfi2569ye Parts

This door mullion is the vertical flipper rail that mounts to a refrigerator French door. It swings closed to cover the center gap, helping complete the door seal and reduce warm air leaks and condensation between the doors.

• Provides the pivoting center rail that mates with the opposite door to complete the seal
• Replace if cracked, broken, warped, or if the flipper won't fold or spring closed
• Common symptoms: door won't close smoothly, visible gap/light between doors, moisture or frost along the center seam
• Helps restore a proper air seal for consistent cooling performance

• Disconnect power and clear door bins before servicing
• Open the door; release the upper and lower retainers and lift the old mullion off its hinge points
• Position the new mullion, secure the retainers, and verify it pivots and seals correctly
• Check door alignment and gasket contact along the center seam

A replacement door hinge assembly that secures the appliance door and lets it pivot smoothly. Installing the correct hinge restores proper door alignment so the door opens and closes reliably and reduces uneven gaps. What it does:

• Provides the pivot point that supports the door and maintains alignment.
• Replaces cracked, worn, or bent hinges that cause door sag or misalignment.
• Helps the door close fully and stay seated to reduce drafts and uneven sealing.
• Restores normal hinge movement to eliminate sticking or noisy operation.

• Disconnect power to the appliance before beginning any repair.
• Support the door while removing and installing the hinge to prevent injury or damage.
• Use the correct hand tools and keep track of mounting hardware; do not overtighten fasteners.
• After installation, check door swing and alignment; adjust as needed.

A vertical mullion assembly that restores the finished trim along the refrigerator door edge and covers the gap between doors for a clean appearance. Replaces cracked, broken, or loose mullion trim to improve fit and finish. What it does:

• Covers the vertical gap between refrigerator doors and provides a finished interior edge
• Hides and protects any wiring or fasteners routed along the door edge
• Restores proper door trim when the original mullion is cracked, split, or loose
• Helps reduce visible moisture or frost build-up along the door seam caused by damaged trim

• Disconnect power to the appliance before starting any repair to avoid injury
• Typically installs with a few fasteners or snaps into place; keep mounting screws from the original part if reusing
• Handle trim pieces carefully to avoid cracking; use non-marring tools to pry if needed

This is the mechanical shutoff arm for the ice maker. It lifts to pause ice production when the bin is full and lowers to resume, restoring proper on/off control to help prevent overfilling or a no-ice condition.

• Starts and stops ice production based on arm position (down = on, up = off)
• Replaces a bent, broken, or missing arm to restore proper shutoff function
• Helps address: ice maker won't stop making ice/overfills the bin
• Helps address: ice maker won't make ice because the arm is stuck in the up/off position

• Disconnect power to the refrigerator before servicing
• Remove the ice bin for access; withdraw the old arm from the pivot holes
• Insert the new arm into the ice maker pivot points; ensure smooth up/down movement
• Restore power and verify the arm raises to stop and lowers to start ice making

This is the refrigerator's sealed-system compressor. It pressurizes and moves refrigerant through the system to remove heat from the cabinet, restoring consistent cooling performance when the original compressor has failed or lost capacity. What it does and common symptoms:

• Pumps and circulates refrigerant through the evaporator and condenser to remove heat
• Maintains target temperatures in both fresh food and freezer sections
• Symptoms of failure can include: no cool/poor cooling, unit warms up after short operation, humming then clicking from the compressor area, or repeated thermal overload trips
• Runs but not cool effectively when the compressor is weak or internally damaged (after ruling out start components and charge issues)

• 1 compressor

• Disconnect power before servicing; sealed-system work involves high pressure and high temperatures
• Sealed-system repairs require EPA Section 608 certification and specialized tools (gauges, vacuum pump, brazing equipment)
• Replace the filter-drier, braze connections properly, evacuate to deep vacuum, and charge to the model's specification
• Related components (start device/overload, run capacitor, controls) are tested before condemning the compressor

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

This drain tube gasket seals the connection between the drain tube and its mating port to prevent leaks. A tight seal helps keep water where it belongs and protects surrounding components from moisture damage.

• Creates a watertight seal at the drain tube connection point
• Can help address water leaks around the drain area
• Deterioration, cracking, or hardening of the old gasket may cause seepage
• Replacing a worn gasket can restore proper leak prevention

• Unplug the appliance and shut off water supply before service
• Place a towel or pan to catch residual water when disconnecting the tube
• Inspect the tube and mating surfaces; clean before installing the new gasket
• Do not overtighten fittings; verify a snug, even seal and check for leaks on first run

This small extension mounts on the end of the ice maker's bail/shut-off arm. It restores the proper reach so the ice maker senses a full bin and stops production, helping prevent overfilling and ice jams. What it does:

• Attaches to the end of the ice maker bail/shut-off arm to extend its reach
• Helps the ice maker detect a full ice bin and pause ice production
• Replace if cracked, warped, or missing from the arm
• Common symptoms: ice maker won't stop making ice, ice overfilling or spilling into the freezer

• 1 shut-off arm extension

• Unplug the refrigerator before servicing
• Remove the ice bin for access and locate the ice maker bail/shut-off arm
• Install the extension on the arm as designed; ensure free movement and proper alignment with the bin
• Restore power and verify the arm moves freely and shuts ice production off when raised

This cover replaces a cracked, warped, or missing cover on your appliance. It protects internal components and restores the correct fit and finish so parts stay secured and the unit operates as designed.

• Shields internal components from debris and moisture
• Helps maintain proper airflow, water path, or guarding as designed
• Restores fit/finish and keeps parts secured
• Common signs of failure: cracks, broken tabs, discoloration, or a cover that won't stay in place

• Disconnect power and shut off water/gas before servicing
• Note the original orientation and transfer any screws/clips from the old part
• Align tabs and fasteners; avoid overtightening to prevent damage
• After installation, test operation and ensure no interference or leaks

This hinge cover assembly conceals and protects the door hinge area, providing a clean look while shielding wiring and moving parts from dust and moisture. It restores proper coverage if the original cover is cracked, missing, or loose.

• Covers the hinge area to protect components and improve appearance
• Helps prevent debris intrusion around the hinge mechanism
• Common fix for a broken, missing, or damaged hinge cover
• May help if the hinge area is exposed or rattling due to a loose cover

• Unplug appliance before service; shut off water if applicable
• Use a non-marring tool to release clips or tabs; avoid prying on finished surfaces
• Transfer any reusable screws or trim from the old cover
• Confirm secure engagement of tabs/screws to prevent vibration

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

This factory screw secures appliance components so they stay aligned and firmly attached during everyday use. Replacing a missing or damaged screw helps stop rattles, looseness, and poor fit that can affect performance over time.

• Fastens panels, brackets, or hardware to keep assemblies tight
• Helps correct issues like loose handles, vibrating panels, or misaligned parts
• Restores proper fit after a screw is stripped, corroded, or lost
• Built to match the original thread and length for reliable engagement

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct driver to avoid stripping the head or threads
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Replace any companion fasteners that are worn or missing for even clamping

This gasket for the damper assembly provides a replacement seal that helps keep compartments properly isolated and reduces air leakage. Replacing a worn gasket restores more consistent airflow and supports stable internal temperatures. What it does:

• Seals the damper opening to reduce unwanted air transfer between compartments.
• Helps the damper close and regulate airflow for more consistent temperature control.
• Common symptoms of a failing gasket: temperature swings, frost or moisture buildup, and noisy or improperly closing damper.
• Restoring a proper seal can improve cooling consistency and help avoid overworking the compressor.

• Disconnect power to the appliance before attempting service.
• Remove interior items and any trim panels needed for damper access; use gentle prying to avoid damage.
• Seat the new gasket fully into the damper groove and verify smooth damper movement before replacing panels and contents.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Color: White