Mhw6000xw Parts

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This is the service tech sheet for the appliance. It provides wiring diagrams, diagnostic information, and troubleshooting procedures to help accurately identify and resolve performance issues.

• Contains official diagnostic steps and wiring information
• Helps trace error conditions and electrical problems
• Useful when the unit won't start, won't run cycles, or shows fault codes
• Supports accurate troubleshooting to reduce guesswork

• Disconnect power before servicing the product.
• The sheet is typically stored inside the appliance (often behind an access panel or in the door area).
• Handle with dry hands; avoid smudging or tearing diagrams.
• Re-secure in its original location for future service reference.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This replacement ball is the small spherical component used in select Whirlpool-built mechanisms. It acts as a moving seal or detent to control flow or position, restoring smooth, reliable operation when the original ball is worn or missing. What it does:

• Provides the sealing or detent action within its valve, hinge, or track assembly
• Helps prevent backflow, leaks, or unwanted movement
• Restores smooth operation when mechanisms feel rough, bind, or won't stay in position
• Replace if the original is deformed, pitted, corroded, or missing

• 1 ball

• Disconnect power and shut off water supply if applicable
• Access the specific assembly per your model's service documentation and note part order
• Place the ball in its seat/track with any companion spring or seal as designed
• Inspect mating surfaces and related seals or springs and replace if worn

Replacement control knob that restores manual command of heat and function settings on compatible Whirlpool appliances. Its push-on design gives a secure grip and straightforward replacement for cracked, stripped, or missing knobs. What it does:

• Lets you set and adjust temperature, burner heat level, and basic oven or cooktop functions.
• Restores control when the original knob is loose, cracked, stripped, or missing.
• Push-on fit provides a secure connection to the control shaft and reliable tactile feedback.
• Improves visibility and usability when original markings have worn away.

• Disconnect power or unplug the appliance before servicing to reduce risk of shock or injury.
• Remove the old knob by pulling it straight off the control shaft; avoid twisting or levering against adjacent parts.
• Align the knob indicator with the control shaft splines and push the new knob fully onto the shaft until seated.
• Reconnect power and test controls at low settings to ensure proper fit and operation.

This water level pressure switch monitors air pressure from the appliance tub and signals the control when the correct fill is reached. Replacing a faulty switch restores accurate fill levels and allows the cycle to advance properly.

• Detects tub water level via the attached air hose and converts it to an electrical signal
• Instructs the control to start/stop water fill and progress through the cycle
• Helps prevent overfill and underfill conditions
• Common symptoms: continuous filling, no/short fill, incorrect water level, won't advance past fill, or water-level/pressure-sensor errors

• Disconnect power and shut off water supply before servicing
• Access the switch (location varies by model); note hose and wire orientation
• Transfer and secure the air hose and connector(s); ensure the hose/air trap is clear, unkinked, and sealed
• After reassembly, run a fill test to ensure proper operation

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

This is the pull-out dispenser drawer assembly for a washer. It holds and channels laundry products into the dispenser housing so each additive is released at the right time, restoring smooth operation and proper dispensing. What it does:

• Holds detergent and additives and directs them into the wash at the correct stage
• Restores smooth open/close action of a worn or broken drawer
• Helps resolve issues like detergent remaining in the drawer after a cycle
• Addresses leaks or drips from a cracked or warped dispenser drawer

• 1 dispenser drawer assembly

• Unplug the washer and turn off water supply before servicing
• Pull the old drawer out; depress the locking tab(s) to remove
• Transfer any reusable inserts/caps from the original drawer if applicable
• Slide the new drawer into the rails until it clicks; run a quick cycle to check for proper dispensing and leaks

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This replacement bracket secures a component within your appliance. It restores a firm, correctly aligned mounting point so parts stay stable and operate as intended without looseness, shifting, or vibration. What it does:

• Provides a rigid mounting point on the appliance frame or cabinet
• Holds the mating component in proper position and alignment
• Helps reduce rattles, vibration, and movement
• Replaces a bent, cracked, stripped, or missing bracket

• 1 bracket

• Disconnect power; turn off gas or water before servicing
• Note the original bracket's orientation and fastener locations before removal
• Install using appropriate screws/fasteners; do not overtighten
• Verify alignment and clearances, then test operation before final reassembly

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This replacement cam is a small drive component that converts rotational input into controlled movement inside the appliance mechanism. It helps the linked assembly engage in the correct sequence for smooth, reliable operation.

• Guides and times movement of the connected parts for proper engagement
• Restores smooth operation when the original cam is worn, cracked, or stripped
• Helps address binding, clicking/popping noises, intermittent operation, or parts not actuating
• Helps maintain alignment to reduce wear on mating components

• Disconnect power to the appliance; also shut off water supply
• Access the mechanism per your model's service information; note the cam's orientation before removal
• Transfer any springs, clips, or spacers from the original cam as needed
• Inspect mating followers/pivots for wear; test movement by hand before reassembly

This replacement lever is a small mechanical link that engages or releases its mating mechanism inside the appliance. Replacing a worn or broken lever restores crisp actuation and reliable operation of the related control or latch. What it does:

• Transfers motion from a button, handle, or cam to the connected mechanism (such as a latch, switch, or dispenser component)
• Ensures the mechanism moves fully and smoothly
• Wear or breakage can cause a loose feel, incomplete travel, or no response when pressing/pulling the control
• Visible cracks, missing tabs, binding, or intermittent operation are common signs it needs replacement

• 1 lever

• Disconnect power before servicing; also turn off water supply
• Access the assembly for your model per the service/parts diagram
• Note orientation of any springs or clips connected to the original lever; transfer them if present
• Reinstall with existing fasteners and test operation before reassembly