Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fresh food section. Color: clear. Measures about 3 inches in diameter.
Replaced the temp controller Read more
Refrigerator not cooling properly? A clogged filter drier prevents proper refrigerant flow. Requires professional installation due to sealed system.
Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly. Read more
Replaces burned-out, dim, or flickering refrigerator light bulbs to restore clear interior visibility. Easy DIY installation—just unscrew old bulb and install new one. Verify fit by your model number.
Ordered new bulb from APPros. Read more
Seals the fresh food door to keep cold air in and prevent condensation. Replace when torn, deformed, or no longer sealing evenly. Confirm fit by model.
Ordered gasket and viewed video. My door was different and had screws holding inner door panel (just the plastic shelves). I easily removed the screws, the old gasket was easily removed, and the new one inserted without needing to perform any cutting or putty knife as shown on video. Read more
Right-side rail supports and guides your refrigerator's meat or deli drawer for smooth operation. Replace if cracked, broken, or worn to prevent tipping.
Popping the old draw glides off was the toughest part of the job, ad even that was fairly easy, once I noticed the little retaining tabs near the front of the drawer. Pushed in on the tabs, while pushing back on the drawer glide rail and it popped right off. One minor problem I did note: When the rollers were installed on the shoulder screws, they would not turn. One roller just had a burr around the inside edge of the hole. The other the entire bore was a bit undersized, creating a snug fit.... Read more
Fix ice buildup in freezer and warm fridge temps. This defrost thermostat monitors evaporator temperature to control defrost cycles. DIY-friendly repair.
After watching numerous videos I was able to discern that the problem was with one of the following: the timer, the heater, or the thermostat. a short time check showed me that the timer was working so that narrowed it down to the other two. Not having the necessary tools to check those two I ordered both parts. Once the parts came and I took out the old parts it was quite evident that it was the heater since it had black burn marks on it. I decided to install the thermostat also since it... Read more
Seals freezer door to prevent warm air leaks and frost buildup. Replace when worn, cracked, or not sealing properly. Confirm fit with your model number.
I ordered a new gasket and my husband and I installed it. Read more
This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.
I ordered the part from you which arrived much sooner than expected. I replaced the Rail-Mulln. It was so easy to fix, next time I'll let my wife do it. Read more
Drawer roller enables smooth gliding of refrigerator drawers. Replace if drawer falls off track, sticks, or roller is cracked. Verify fit with your model.
Refrigerator not cooling or compressor won't start? This overload protector prevents motor damage from overheating. DIY-friendly fix in under 30 minutes.
Used a muiltimeter to test all parts and ohm'ed out all parts. found out condenser fan motor seized up [open winding in motor] replaced that, and found that also caused the compressor overload and relay to fail, from over heating and over cycling, replaced both parts, powered up the refrigerator retested all electrical parts checked amp reading on all parts under load conditions,works good know, hope to get another 15 years out of this refrigator, its a maytag. over 20 years old. Read more
Lower hinge pin serves as the pivot shaft for your refrigerator door. Replace this part if worn, bent, broken, or missing to restore smooth door movement.
Temporarily stuck a BMW lug bolt through the bracket and pivot opening to secure the door on the base, then waited just 3 days for the exact parts to come in from AppliancePros. Searching for the appliance model number brought me to the Appliance Pros website where finding the exact parts was quick and easy. Getting the correct part installed was a bit more involved as I had to remove and reinstall the bracket once the hinge pivot was installed, but it was quick and easy with my son holding the... Read more
Replaces a worn or heat-damaged refrigerator light socket to restore interior lighting. Install when bulbs won't light despite replacement. Confirm fit by model number.
I bought a new bulb but it did not work. Then the super looked at it and realized the socket was not good. Read more
Fridge clicks or hums but won't cool? A failed start relay prevents the compressor from starting. Simple DIY repair—just pull off and replace.
I replaced the Relay-Ptc and that solved the problem. I could see that there was a problem with the relay because it was arcing inside and you could see a glow coming from the inside. when I removed it from the compressor I shook it and I could hear it rattling and news for sure it was the problem Read more
Fix frost buildup and warm temperatures caused by a faulty defrost thermostat. This sensor controls the defrost cycle. Simple 20-minute repair.
I removed the back panel in freezer and light cover then the following: remove the rusted clips, unplug heater and replaced new heater, the thermostat defrost I unfasten, clip on replacement and connected plugs. Read more
This heater clip secures the defrost heater in your refrigerator. Keeping the element properly positioned helps the defrost system work as designed and reduces rattling or damage from a loose or misaligned heater.
Replaced with new element Read more
Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:
Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new Read more