Neptune Parts

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This metal clamp secures the exhaust hose connection to the dryer's outlet port, preventing air leaks and ensuring proper ventilation. Replace if you notice reduced airflow, lint buildup around the connection, the hose feels loose, or drying times have increased.

To order indicator light use WP903115.

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

Replace your washer's door boot seal when you notice leaks, tears, or mold around the door opening. Creates a watertight barrier. Confirm fit with your model.

Fix a washer that won't drain or leaves standing water by replacing a failed drain pump. This assembly moves water out during drain and spin cycles.

This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.

• Encloses and supports the blower wheel while channeling air from the drum to the exhaust
• Maintains correct airflow and back pressure for efficient drying performance
• Replace if the housing is cracked, warped, melted, or otherwise damaged
• Typical symptoms include weak vent airflow, longer dry times, rattling or scraping from the blower area, or visible lint leakage

• Disconnect power; if gas, also shut off the gas supply
• Access the blower area by removing the lower/front panel and lint ducting as required by your model
• Transfer the blower wheel and any brackets from the old housing; clean lint from ducts before reassembly
• Ensure the housing seats fully and all duct connections are tight; spin the blower by hand to verify clearance before restoring power

This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.

This timer with a built-in chime controls cycle sequencing and provides an audible end-of-cycle signal so the appliance finishes and alerts you when a cycle is complete. It replaces a failed or silent control timer. What it does:

• Advances and times cycles so the appliance runs through its programmed steps.
• Sounds an audible chime at the end of a cycle to notify you the cycle is finished.
• Can cause missed cycle advances or no end-of-cycle alert when it fails.
• Common symptom: no chime or the appliance won't progress through cycles.

• Disconnect power to the appliance before beginning any service.
• Access usually requires removing the control panel or console; retain screws and knobs for reassembly.
• Transfer any mounting brackets or knobs from the old unit to the new one if required.

Loud banging or excessive shaking during spin? This shock absorber stabilizes the tub and reduces vibration. DIYers report quiet operation after replacement.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

Decorative cover ring that surrounds the dryer timer dial, providing labeled settings. Replace if cracked, broken, or worn from frequent use.

To order indicator lens use WP22001948.

Washer shock absorber mounts between tub and base to control movement during spin. Replace when washer vibrates excessively, walks, or makes loud noise.

This is a rubber gasket that sits inside the water inlet hose connection on your washing machine. It creates a watertight seal between the hose fitting and the water supply valve to prevent leaks. Replace this gasket if you notice water dripping from the hose connections at the back of the washer.