Pdw8600 Parts

Specs: B-16 HXW 1/2 SS

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

This gasket trim seals the dishwasher door opening, helping contain moisture and steam during cycles. Replacing a worn, torn, or missing trim restores a proper barrier and helps prevent drips or condensation at the door area. What it does:

• Provides a moisture/steam barrier where the door meets the tub opening
• Helps protect the console and surrounding surfaces from escaping steam
• Cushions the door for a snug, secure close
• Common signs to replace: cracked, flattened, deformed, or missing trim; moisture around the door edges; visible wear

• 1 gasket trim

• Disconnect power and turn off the water supply before servicing
• Open the door and pull the old trim straight out of the channel
• Clean the groove; press the new trim fully into the channel without stretching
• Open and close the door to confirm even contact; reseat if needed

Lower dishwasher rack roller axle only. Color: White. Measures about 1 inch wide by 1 inch high by a 1/2 inch deep. For Gray color order part number WD35X21041.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This mid-spray conduit routes wash water from the circulation system to the middle spray arm, delivering consistent coverage to the center rack. Replacing a cracked or clogged conduit can restore washing performance and help prevent leaks inside the tub.

• Directs wash water from the pump to the mid-level spray arm
• Maintains proper flow for the middle wash zone and spray arm rotation
• A damaged or obstructed conduit can cause poor cleaning on upper racks or weak/erratic spray
• Cracks, broken tabs, or loose sealing can lead to leaks from the rear of the tub

• Disconnect power and water; wear gloves to protect hands
• Remove rack(s) as needed, release rear-wall fasteners/clips, and detach the conduit from its connections
• Align and fully seat the new conduit at all docking points until tabs lock securely
• Run a short test cycle to check for leaks and proper spray operation

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 8-18 AB TSQ 5/8 SS

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This bracket supports and secures the detergent/rinse-aid dispenser to the inner door of your dishwasher, keeping it aligned and sealed so detergent stays contained until the cycle releases it.

• Rigidly mounts the dispenser assembly to the inner door panel
• Helps maintain gasket compression to reduce leaks around the dispenser perimeter
• Keeps the dispenser flush and properly aligned for consistent operation
• Common signs of damage: loose or wobbly dispenser, visible cracks in the bracket, moisture or drips around the dispenser area, difficulty tightening the dispenser to the door

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support the dispenser while loosening hardware
• Transfer the bracket and reuse existing mounting screws; ensure the dispenser gasket is clean and seated before tightening
• Tighten screws evenly without overtightening; run a short cycle to check for leaks around the dispenser

This hinge cup mounts at the lower front corner of the dishwasher tub to cradle the door hinge arm as the door pivots. Replacing a worn cup restores smooth, quiet door operation and helps prevent hinge misalignment.

• Supports the door hinge arm where it meets the tub frame
• Provides a smooth pivot point to reduce friction and wear
• Helps keep the door aligned and opening/closing evenly
• Failure signs can include creaking, binding, or the door dropping abruptly; visible wear or cracking on the cup

• Disconnect power and shut off the water supply before servicing
• Support the door and relieve hinge spring tension as needed
• Remove the toe panel/kickplate to access the hinge area
• Install the cup and ensure the hinge arm seats fully; test door movement before reassembly

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

Color: gray. Measures about 1 inch high by 1-1/2 inches deep.

Size: 10-32 GXTT FLP.595 S