Pdw8600 Parts

This pump motor hanger is the support bracket that secures the washer pump motor to the appliance frame, helping keep the motor stable during operation for reliable drainage performance. What it does:

• Holds the pump motor in the correct position to prevent vibration and misalignment
• Maintains pump-to-housing alignment so the drain pump can move water effectively
• Helps reduce unusual noise or movement caused by a loose motor mount
• Fits where the motor attaches to the washer chassis; replaces worn or bent hangers

• Disconnect power before starting any repair and follow basic electrical safety
• Basic hand tools required; keep original fasteners unless damaged
• Inspect pump and motor for wear while replacing the hanger

This part is an upper dishrack assembly for dishwashers. The purpose of this part is to hold dishes and cookware during the washing process. There are two dish racks per unit, and this particular dishrack goes on the top of the unit. The lower dishrack assembly is sold separately. Over time, the upper dishrack assembly may rust due to the coating breaking down and water corroding the metal. If this happens, the dishrack assembly will become brittle and less structurally sound and will need to be replaced. If the attached rails have broken and will not attach to the sides of the dishwasher and slide appropriately, this part may need to be replaced.This upper dishrack assembly is compatible with dishwashers that are manufactured by the GE and Whirlpool brands. This particular component is an OEM part that is sourced directly from the manufacturer and is sold individually.

The Middle Spray Arm is an OEM replacement part for GE dishwashers. It is an internal component responsible for distributing water and washing accessories to dishes located in the center rack of the dishwasher. 

Symptoms of a bad middle spray arm include:

• Dirty dishes located in the center rack, even after a full wash cycle
• Noticeably reduced water pressure from the center spray nozzle 
• Clogged or blocked spray holes in the arm

Causes of a bad middle spray arm can be normal wear and tear, mineral buildup obstructing spray outlets, or physical damage to the arm itself.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher vent cover mounts on the inner door and shields the exhaust opening. It directs moist air out during drying while helping keep spray and debris out of the vent path to protect internal components. What it does:

• Covers the door vent opening and helps guide exhaust airflow during the dry cycle
• Helps keep water spray and debris from entering the vent assembly
• Supports proper moisture management around the top of the door/control area
• Replace if the cover is cracked, warped, loose, or missing, or if steam/water escapes from the vent area

• 1 vent cover

• Disconnect power at the breaker and turn off the water supply; wear cut-resistant gloves
• Access is through the door; on many models the inner door panel must be removed to reach the vent area
• Ensure any gasket/seal is properly seated and secure the cover evenly—do not overtighten
• Run a short cycle and inspect the vent area for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This float dome sits in the dishwasher's float well and rises with the water level to trigger the float switch and stop filling. Replace a cracked or missing dome to restore reliable water-level control and overfill protection.

• Moves up and down with the water level to actuate the overfill/flood switch
• Helps prevent overfilling by signaling the inlet valve to shut off at the correct level
• Guides and shields the float mechanism from dishes and debris
• Common symptoms: broken or missing dome, float sticking, dishwasher won't fill or keeps filling

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float area on the tub floor
• Lift straight up or twist to remove the old dome; clear any mineral/debris from the float well
• Seat the new dome and run a brief fill test

This water inlet cover replaces a cracked or missing inlet-valve trim to protect and conceal the appliance's water inlet area. It restores a finished look while keeping hoses and valve components shielded from debris. What it does:

• Covers and protects the water inlet valve and hose connections from dust and impact
• Conceals exposed hoses and wiring for a cleaner rear-cabinet appearance
• Helps prevent snagging or accidental contact with the inlet valve assembly
• Reduces debris buildup around the inlet area that can affect connections

• Disconnect power to the appliance and shut off the water supply before starting.
• Usually fastens with a few screws or clips—have a screwdriver or nut driver ready.
• Align cover over the inlet valve area, then secure with the original fasteners.
• After installation, turn water and power back on and inspect connections for leaks.

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

A small rack clip that holds stemmed glasses upright during dishwasher cycles, reducing tipping and breakage. Restores proper support for wine glasses and other stemware so they wash safely and stay secure. What it does:

• Secures the stem of wine glasses and goblets to keep them stable during wash and rinse cycles.
• Prevents tipping, chipping, and breakage caused by glasses shifting in the rack.
• Replaces cracked, broken or missing stemware clips that allow dishes to move or clink.
• Helps reduce noise from glassware hitting the rack when the clip is damaged or absent.

• Remove dishes and ensure the dishwasher is off before replacing the clip.
• Seats into the dishwasher rack slot—press into place until fully seated; no special tools usually required.
• Refer to your appliance manual for model-specific instructions and safety guidance.

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Right hand side