Pdw9000 Parts

This dishwasher door latch secures the door closed and engages the safety interlock so wash cycles can start and run without leaks or interruptions. Replace a worn or broken latch to restore a firm, reliable door closure. What it does:

• Locks the door to compress the tub gasket and help prevent leaks
• Engages the door switch/interlock so the control can start and continue cycles
• Replaces latches that are cracked, bent, or have weakened/broken springs
• Common symptoms: door won't latch/close, cycle won't start, door pops open mid-cycle, water seeping from the top of the door

• 1 door latch

• Disconnect power and shut off water before servicing
• Open the door and remove inner door panel screws to access the latch
• Note spring and linkage orientation; transfer any reused hardware from the old latch
• Align with the door strike and test closure before fully reassembling

This dishwasher control module assembly is the appliance's electronic brain, directing cycle timing and power to the motor, pumps, water valve, and heater. Replace it to restore proper operation when cycles won't start, advance, or the controls are unresponsive.

• Manages cycle timing and coordinates wash, rinse, drain, and dry operations
• Distributes power to key components based on inputs from the user interface and sensors
• Helps resolve issues such as no start/no response, cycles that won't advance or complete, or recurring error codes/beeping
• Restores consistent control of wash performance and cycle sequencing

• Disconnect power at the breaker or unplug the dishwasher before servicing
• Handle the board by the edges and use ESD precautions; avoid touching components
• Move wiring harnesses over one connector at a time to match positions on the new module
• After installation, restore power and run a test/service cycle or control reset per your model's tech sheet

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

This gasket trim seals the dishwasher door opening, helping contain moisture and steam during cycles. Replacing a worn, torn, or missing trim restores a proper barrier and helps prevent drips or condensation at the door area. What it does:

• Provides a moisture/steam barrier where the door meets the tub opening
• Helps protect the console and surrounding surfaces from escaping steam
• Cushions the door for a snug, secure close
• Common signs to replace: cracked, flattened, deformed, or missing trim; moisture around the door edges; visible wear

• 1 gasket trim

• Disconnect power and turn off the water supply before servicing
• Open the door and pull the old trim straight out of the channel
• Clean the groove; press the new trim fully into the channel without stretching
• Open and close the door to confirm even contact; reseat if needed

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

This dishwasher keypad is the membrane touchpad behind the control console. It registers your button presses so you can select cycles and options. Replacing a failed keypad restores reliable button response and allows the dishwasher to start. What it does / symptoms:

• Provides the user interface for cycle and option selection
• Sends button-press signals through the ribbon connector to the electronic control
• Buttons are unresponsive or work intermittently
• Dishwasher won't start when Start/Reset is pressed
• Indicator lights may come on but controls don't respond to input

• One keypad

• Disconnect power at the breaker before servicing
• Access the console/door area to reach the keypad and control
• Carefully release the ribbon connector; avoid creasing or damaging it
• Ensure the ribbon is fully seated and correctly oriented in the control board connector before reassembly

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This keypad is the membrane switch mounted behind the dishwasher's control panel. It registers your button selections and sends them to the electronic control, helping restore consistent response when keys are unresponsive, intermittent, or require excessive pressure. What it does:

• Registers cycle, option, and Start/Reset inputs on the console
• Sends those selections to the electronic control for proper operation
• Failure symptoms include: some or all buttons not responding, needing to press very hard, erratic input, or the cycle not starting from the console
• Can also present as stuck/continuous key input or random beeping

• 1 keypad

• Disconnect power at the breaker before servicing; the control console contains live voltage
• Open the door and remove inner-door screws to access the control console
• Note ribbon-cable orientation; insert straight and fully into the board connector without creasing the flex
• Handle electronics with dry hands and ESD care; reassemble without overtightening screws

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 8-18 AB TSQ 5/8 SS

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This bracket supports and secures the detergent/rinse-aid dispenser to the inner door of your dishwasher, keeping it aligned and sealed so detergent stays contained until the cycle releases it.

• Rigidly mounts the dispenser assembly to the inner door panel
• Helps maintain gasket compression to reduce leaks around the dispenser perimeter
• Keeps the dispenser flush and properly aligned for consistent operation
• Common signs of damage: loose or wobbly dispenser, visible cracks in the bracket, moisture or drips around the dispenser area, difficulty tightening the dispenser to the door

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support the dispenser while loosening hardware
• Transfer the bracket and reuse existing mounting screws; ensure the dispenser gasket is clean and seated before tightening
• Tighten screws evenly without overtightening; run a short cycle to check for leaks around the dispenser

This hinge cup mounts at the lower front corner of the dishwasher tub to cradle the door hinge arm as the door pivots. Replacing a worn cup restores smooth, quiet door operation and helps prevent hinge misalignment.

• Supports the door hinge arm where it meets the tub frame
• Provides a smooth pivot point to reduce friction and wear
• Helps keep the door aligned and opening/closing evenly
• Failure signs can include creaking, binding, or the door dropping abruptly; visible wear or cracking on the cup

• Disconnect power and shut off the water supply before servicing
• Support the door and relieve hinge spring tension as needed
• Remove the toe panel/kickplate to access the hinge area
• Install the cup and ensure the hinge arm seats fully; test door movement before reassembly

Size: 10-32 GXTT FLP.595 S

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

Color: gray. Measures about 1 inch high by 1-1/2 inches deep.