Pdw9280looss Parts

This latch keeper assembly secures the appliance door for a reliable latch connection and helps restore proper door closing. Replace a worn or broken keeper to stop the door from popping open or failing to engage. What it does

• Provides the capture point for the door latch/bolt so the door stays closed during operation
• Restores proper door engagement when the keeper is cracked, warped, or broken
• Helps prevent cycles from stopping due to a door that won't fully latch
• Fits into the cabinet striker area and works with the existing latch mechanism

• One latch keeper assembly (single piece)

• Disconnect power (and water, if applicable) before beginning any repair
• Access is usually from the front by removing the door trim or the cabinet striker panel — verify your model's disassembly steps
• Inspect the mating latch for wear and replace if both parts show damage

Specs: 8-18 va trt 7/16

Dishwasher rack tine clip. Used to hold the tines in place within the rack. Color: gray. Measures about 1 inch wide by 1 inch high by 1-1/2 inches deep.

The Upper Spray Arm Bearing is an OEM part for GE dishwashers. It supports the upper spray arm, allowing it to rotate smoothly and distribute water evenly throughout the dishwasher. This ensures that all dishes receive a thorough cleaning during each cycle.

Over time, the upper spray arm bearing can wear out or become damaged. Causes of a bad bearing can include repeated use, mineral buildup from hard water, or physical damage due to mishandling.

Symptoms of a bad Upper Spray Arm Bearing include:

• The upper spray arm not rotating properly
• Ineffective cleaning of dishes on the upper rack
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket Spring is an OEM part for GE dishwashers. It plays a crucial role in maintaining a tight seal around the dishwasher door, ensuring that water does not leak during operation. This spring helps keep the door gasket in place, providing a reliable and consistent seal.

Over time, the gasket spring can wear out, lose tension, or become damaged due to repeated use and exposure to the dishwasher’s high temperatures and moisture. A faulty spring can compromise the effectiveness of the door gasket, leading to potential leaks and inefficient washing cycles.

Symptoms of a bad gasket spring include:

• Water leaking from the dishwasher door
• Difficulty closing or latching the dishwasher door securely
• Reduced cleaning performance due to improper sealing

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher flood switch seal sits around the flood/leak switch to create a watertight barrier at the switch opening. Replacing a cracked or flattened seal helps stop under-unit drips and keeps leak detection working properly.

• Forms a watertight seal where the flood switch mounts
• Helps prevent water from entering the base pan
• Common signs include water under the unit or visible wear on the old seal

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick; pull the unit forward if needed to access the flood switch
• Release the flood switch, remove the old seal, and seat the new seal evenly—do not overtighten
• Reassemble and run a short fill/rinse while checking closely for leaks

Upper dishrack roller and axle kit includes: 4 rollers and 4 axles.

The front door of a dishwasher is operated in part by the use of door springs. There are typically two door springs on most models. The door spring helps the user open and shut the door efficiently. If the door springs are worn out or broken, a replacement part is required.A visual inspection will determine if a door spring is missing, damaged, or worn out. If the dishwasher door no longer opens and closes smoothly, it's an indication that a repair is required. Replacing a dishwasher door spring is a straightforward process. Locate the existing springs and remove them. Line up the new door springs and hook the ends into place. Wear gloves for protection. Disconnect the dishwasher before starting the replacement.This door spring is an authentic OEM replacement part. It is sold individually. The component is made of durable, high-quality metal materials. The replacement door spring comes sourced directly from the manufacturer. The door spring is fitting for several different models of dishwashers. The part can be installed in General Electric, Hotpoint, and RCA devices.