Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces a worn, cracked, or broken arc-style freezer handle on your refrigerator. Restores secure grip and original appearance for confident opening.
I ordered the parts & installed the handle. Read more
Replacement arc-style door handle for refrigerator doors and freezer drawers. Installs on door studs for secure grip. Needed when original is cracked or broken.
Ordered a replacement handle. Read more
Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.
Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more
Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.
I replaced the lever asm. and spring Read more
If your refrigerator runs but doesn't cool or fails to start, the compressor start device may have failed. This relay and overload combo helps restore cooling.
Replaced part. Read more
The Dispenser Shield is an OEM part for GE refrigerators equipped with water and ice dispensers. This shield acts as a protective cover for the dispenser area, preventing accidental spills or debris from entering the internal mechanisms.
Symptoms of a faulty dispenser shield:
Causes of a bad dispenser shield can include impact or mishandling, exposure to excessive moisture or freezing temperatures, or general wear over time.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.
Tried gluing it together - did not hold. Ordered a new Shield Dispenser. The new one came without the wire spring installed. Used the wire spring from the old one. Works OK - so far. Lesson re-established --- Never toss old parts until repair is complete. Read more
This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.
Refrigerator door gasket creates an airtight seal to keep cold air in. Replace if door won't seal, frost builds up, or gasket is torn. Confirm fit with model.
Replaced with new. Read more
Replace your refrigerator door gasket to restore the airtight seal and prevent cold air loss. Install when gasket is cracked or loose. Confirm fit.
I ordered a new set of gaskets and filter from Appliance Pros.com. Watched a video on changing the gaskets and got it done. Read more
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more
This kit includes left and right slide rail holders that secure the drawer slide rails inside the freezer compartment of the refrigerator. The holders keep the drawer gliding smoothly on its tracks when opening and closing. Replace this kit if the freezer drawer is sagging, sticking, or falling off track due to broken or worn slide rail holders.
Replaced both tracks. Read more
Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.
I ordered my parts. It was a breeze thanks to appliancepartspros.com. I received the parts the next day. Installed them myself. Read more
Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.
Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more
White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.
Stores chilled water inside your refrigerator for the door dispenser. Replace if cracked, burst, or leaking along the seams to restore proper water supply.
Replaced the water tank and water valve assembly. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.