Pod301j/01 Parts

The Sensor is an OEM replacement part for Bosch ranges. It monitors conditions inside the oven compartment such as temperature and diagnosing faults. 

Symptoms of a bad sensor include:

• The oven not heating or cooking unevenly
• Inaccurate temperature readings displayed  
• Erratic or unpredictable ignition/operation  
• Error codes appearing related to sensor faults

Causes of failure can be normal wear over time from high heat exposure, accidental damage compromising sensor integrity, or intrusion of liquids or debris confusing readings.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore ranges.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This Bake Element is an OEM part for Bosch Wall Ovens. It's responsible for generating heat for baking and cooking. Continuous exposure to high temperatures can cause wear or damage to this component.

What Causes a Bad Bake Element:
Repeated heating and cooling cycles, as well as exposure to high temperatures, can cause the bake element to deteriorate or fail.

Symptoms of a Bad Bake Element:

• Inconsistent oven heating
• Uneven cooking or baking
• The oven fails to reach set temperatures

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door seal restores a tight barrier between the oven door and cavity. Replacing a worn gasket helps your oven reach and hold temperature, reduces heat escaping at the door edges, and supports more consistent baking and roasting results.

• Creates a heat-resistant seal around the oven opening
• Helps the oven preheat and maintain set temperature
• Limits heat, steam, and odors from escaping at the door
• Typical signs it needs replacement: visible tears or flattening, heat felt around the door, longer preheat/cook times, or uneven baking

• Disconnect power at the breaker and let the oven cool completely
• Open the door, pull the old seal from its channel, and clean the groove
• Press the new seal evenly into the channel without stretching; ensure corners seat fully
• Close the door to verify uniform contact all around and adjust as needed

The Oven Door Seal is an OEM part for Bosch ovens and ranges. This door seal fits snugly around the outer edge of the oven door to provide an effective air seal when closed.

Causes of a bad door seal can include damage from normal wear and tear over time, compression from repeated opening and closing of the door, or heat exposure leading to cracking or warping.

Symptoms of a bad door seal include:

• Inefficient or slow heating
• Inability to maintain set oven temperature
• Increased energy costs
• Smoke escaping around door edges when baking

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement glass panel restores the smooth, protective surface on the appliance when the original panel is cracked or broken. It helps maintain a clean appearance while shielding the components mounted behind the glass. What it does:

• Forms the visible glass surface on the appliance
• Protects internal components from spills and debris
• Restores a clean, finished look after breakage or heavy scratching
• Common fix for cracked, chipped, shattered, or missing glass

• 1 glass panel

• Disconnect power (and gas, if applicable) and allow the unit to cool completely
• Wear cut-resistant gloves; handle glass carefully
• Transfer any brackets, trim, or seals from the original panel as instructed
• Do not overtighten fasteners; verify proper alignment before restoring power

Replace a cracked or missing shelf and restore a flat, easy-to-clean storage surface inside your refrigerator. This glass shelf fits the designated location in your unit to keep food level, visible, and organized. What it does:

• Provides a flat, stable storage surface inside the fresh food compartment
• Restores capacity when a shelf is broken or missing
• Helps prevent spills and tipping caused by uneven or sagging shelves
• Common signs: cracked/shattered glass, broken edge tabs, shelf won't seat securely, reduced storage space

• 1 refrigerator shelf

• Remove food items; carefully slide the old shelf straight out
• Handle glass with both hands; wear cut-resistant gloves
• Align front/rear edges with the side rails or locator tabs and push straight in until fully seated
• Do not force the shelf; re-align if it binds to avoid damage

This control module is the appliance's main electronic control board. It interprets inputs and energizes components to run the correct sequences, restoring reliable operation when the original board is unresponsive, intermittent, or damaged. What it does

• Coordinates timing and operation of motors, valves, heaters, and other loads
• Monitors inputs from switches and sensors to make decisions
• Distributes power and controls relays/outputs to components
• Common failure symptoms: won't start, controls unresponsive or erratic, stops mid-cycle, or shows error codes

• 1 control module

• Disconnect power before servicing; electronic boards can carry residual charge
• Use ESD precautions; handle the board by the edges and avoid touching components
• Document wiring; move connectors one at a time and ensure they are fully seated and keyed correctly
• Secure the board and any ground straps; reassemble, restore power, and run the model's service/diagnostic test if applicable

This door latch secures the appliance door and helps enable normal operation by keeping the door closed and latched during cycles. Replacing a worn or broken latch restores proper door engagement and reliable start/lock behavior. What it does:

• Secures the door closed so the appliance can run and complete cycles
• Engages with the strike to maintain a tight, consistent seal during operation
• Helps the control detect a closed/locked door and permit cycle start
• Commonly replaced when the door won't stay closed, won't lock, or the unit won't start

• One replacement door latch

• Disconnect power and water before beginning any repair
• Access may require removing the inner door panel or front trim—keep fasteners organized
• Verify alignment of the latch and strike before reassembly to ensure proper engagement
• If the latch has electrical connectors, reconnect securely and avoid pinching wires

This factory fixing kit provides the mounting hardware needed to secure the applicable component or panel on your appliance. Replacing worn or missing fasteners restores proper alignment and a solid, rattle-free installation.

• Secures panels, brackets, or trim to the appliance chassis or door
• Helps prevent shifting, vibration, and rattling during operation
• Restores correct alignment and fit when hardware is missing or stripped
• Useful during initial installation or when re-installing serviced parts

• Disconnect electrical power; if your appliance is plumbed, shut off water before servicing
• Follow your model's installation/service instructions for exact hardware locations and orientation
• Tighten hardware evenly; do not overtighten to avoid damaging plastic or sheet metal
• Verify alignment and smooth operation before restoring power and/or water

This socket is an electrical connector used to join wiring or plug-in components, restoring a secure connection for reliable appliance operation. It replaces a worn or damaged socket to help prevent intermittent power or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Restores proper contact when a loose, corroded, or broken socket causes intermittent operation
• Helps prevent arcing or poor connections that can lead to component failure
• Used where a plug-in or push-fit electrical connection is required

• One socket

• Disconnect power to the appliance before inspecting or replacing the socket
• Replace only with the exact socket type specified for your appliance

This is a replacement heating element that warms dishwasher wash water so dishes come out cleaner and drier. Restores the appliance's ability to heat water during cycles for improved cleaning and drying performance. What it does:

• Heats the dishwasher's wash water so detergents activate and soils break down
• Supports heated drying and reduces leftover moisture on dishes
• Helps resolve symptoms such as poor cleaning, weak drying, or heater-related error codes
• Works as the primary electric heating component in the dishwasher's sump/tub area

• One heating element

• Disconnect power to the appliance before starting any repair to avoid shock
• Access typically requires removing the lower access panel and/or tub components; keep track of fasteners
• Inspect wiring and connectors for heat or corrosion damage and replace as needed

This trim plate is a decorative panel that restores the finished look of the appliance opening and helps cover gaps around the control or access area. It provides a clean, factory appearance and prevents dirt from collecting in the seam. What it does:

• Covers and finishes the edge of an opening or control area for a seamless appearance
• Helps keep crumbs, dust and spills from entering gaps around the appliance face
• Replaces bent, scratched or discolored trim that affects the appliance look
• Restores proper alignment where a damaged trim creates visible gaps

• One trim plate

• Disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid scratching the finished surface; use soft gloves if available
• Retain any mounting screws or clips from the original trim and reuse if appropriate

This replacement glass shelf provides a sturdy, easy-to-clean surface for refrigerator storage and restores proper organization after a damaged or missing shelf. Fits the factory shelf guides and supports everyday food containers. What it does

• Replaces a cracked, chipped or missing refrigerator shelf to restore usable storage space
• Provides a flat, stable surface to keep food and containers level
• Helps prevent spills by maintaining a solid barrier between compartments
• Easy-to-clean glass surface resists stains and odors
• Restores proper shelf alignment and load distribution when correctly installed

• Remove food and support the shelf before sliding it out; install by aligning with the shelf guides and seating securely
• Use gloves and eye protection when handling damaged glass; dispose of broken pieces safely
• If the shelf uses separate support clips or rails, retain existing hardware and confirm they are intact before installing
• Unplug the appliance or switch off power at the breaker if working in tight spaces or removing interior lighting components