Ps968s92ss Parts

Restore smooth, precise heat control to your surface burner. This infinite switch sits behind the knob and modulates power to the element so you can dial in consistent low-through-high settings.

• Regulates electrical power to the surface element for adjustable heat levels
• Mounts behind the control knob; each switch controls one burner
• Common failure symptoms: burner won't heat, only heats on high, won't shut off, or heats inconsistently
• Restores proper temperature adjustment and on/off control

• Disconnect power at the circuit breaker before servicing
• Remove the knob and access panel to reach the switch
• Note wire locations or take a photo; move wires to the new switch one at a time onto matching terminals
• Secure the switch, reinstall the knob/panel, restore power, and test the burner

This convection element assembly is the heating ring located behind the rear panel of the oven. It supplies the heat for convection bake/roast, helping deliver even, consistent results when using the convection feature.

• Provides heat around the convection fan to maintain uniform oven temperature in convection modes
• Failure may cause little/no heat in convection, uneven baking/roasting, or extended preheat times
• Replace if the element is open (no continuity), blistered, or visibly damaged
• Direct-fit replacement designed to match original connections and mounting

• Disconnect power at the breaker/fuse and allow the oven to cool completely before servicing
• Remove oven racks and rear interior panel to access the element
• Support and label wires; connect firmly to the element terminals to avoid loose connections
• Avoid bending the element; secure with original hardware and check continuity before reassembly

This radiant bridge element restores heat to the bridge zone on a smooth-top range or cooktop, letting two adjacent burners operate together as one larger cooking area. It replaces a failed element to bring back even, responsive heating.

• Provides the elongated heat source that links two surface elements when the Bridge setting is selected
• Delivers consistent, even heat across larger cookware or griddles
• Replaces a failed or open bridge element to restore normal operation
• Common symptoms: bridge zone won't heat, weak or uneven heating, only works when an adjacent element is on, element tests open

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Lift the glass top or remove the cooktop per your model's procedure to access the element from below
• Note wire positions; move connections to the new element one at a time and secure with existing hardware
• Handle the element carefully; avoid bending or stressing the heating ribbon, verify alignment, then reassemble and test

This glass touch assembly is the stainless front user-interface panel for the oven controls. It replaces a worn, cracked, or unresponsive touch keypad so you can select modes and temperatures and operate your appliance reliably.

• Provides the touch-sensitive keys for cooking modes, temperature, timer, and light functions
• Sends user inputs to the electronic control; failure can prevent starting or adjusting the oven
• Common symptoms: some keys don't respond, random beeping or key error codes, unable to set temperature
• Restores appearance when the front control glass is scratched or cracked

• Disconnect power at the breaker before servicing
• Support the panel and handle glass carefully; remove trim and mounting screws
• Move ribbon/plug connectors one at a time to the new assembly; avoid creasing flex cables
• Reinstall hardware and test all touch keys before final reassembly

This drawer wedge aligns and stabilizes the lower drawer so it opens and closes smoothly and sits flush. Replacing a worn or missing wedge helps eliminate wobble, rubbing, and gaps for better everyday operation.

• Supports and centers the drawer for proper alignment on the slides
• Acts as a spacer/stop to reduce vibration and metal-to-metal contact
• Helps prevent binding and keeps the drawer from popping off the track
• Common symptoms: drawer crooked or sagging, won't close fully, rattles, or feels loose

• Disconnect power and allow the appliance to cool before servicing
• Pull the drawer out to the stops, release the side track tabs, and remove the drawer
• Note the original wedge's position; remove it and install the new wedge in the same orientation (reuse existing hardware if applicable)
• Reinstall the drawer on the rails and verify smooth operation and proper fit

This indicator light module controls the status lights on your range or cooktop, providing clear visual alerts during operation. Replace it to restore reliable, easy-to-see indicators for key functions. What it does:

• Illuminates key status indicators on the appliance's control area
• Helps when functions are active and when conditions require attention
• Common symptoms: lights do not illuminate, stay on continuously, flicker intermittently, or show heat-related damage
• Direct replacement restores normal indicator operation

• Includes: 1 indicator light module

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the appliance to cool completely
• Access the module from the control area per your model's service information; note screw and wire locations
• Transfer connectors one at a time to the new module, secure it, reassemble, and test

The Maintop Glass Assembly is an OEM part for GE electric ranges. As the cooktop surface, this glass panel protects burners from spills and facilitates easy cleaning.

Symptoms of a bad glass assembly include: 

• Cracks, chips or breaks compromising structural integrity 
• Discoloration reducing visibility of burner operations
• Detaching from supporting frame causing a seam gap

Causes can be normal wear from cooking tools and scrubbings. Thermal shocks like sudden temperature changes also weaken glass over time.

This OEM replacement part is compatible with all GE and select Kenmore electric and gas ranges.

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

This is the convection fan motor for select ovens. It drives the rear convection fan to circulate hot air for more even baking and roasting performance.

• Spins the convection fan to move heated air throughout the oven cavity
• Helps protect against uneven cooking, hot spots, or longer preheat times
• A failed motor may hum, seize, not start, or run noisily
• Restores proper convection airflow when the original motor wears out

• Disconnect power before service; oven parts and wiring can be live and hot
• Access is typically from the rear or through the oven interior; remove the fan blade and mounting screws to replace the motor
• Transfer any brackets or wiring in the same orientation; note wire positions or take a photo
• After install, verify the fan spins freely by hand before restoring power

This oven door side insulation sits between the inner and outer door panels to limit heat loss and reduce hot spots along the door edge. Replace when the original is burnt, brittle, or missing to help restore safe thermal performance.

• Provides a thermal barrier along the side of the oven door between panels
• Helps retain oven heat and reduce heat transfer to the outer door surface
• Can help address heat escaping around door edges or a door exterior that feels hotter than normal
• Replace if the insulation is charred, frayed, compressed, or contaminated during service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door and disassemble per your model's service instructions; work on a padded surface
• Wear gloves and eye protection; handle insulation carefully and avoid compressing it
• Do not block vents or air passages during reassembly; note orientation for proper fit

This maintop gasket seals the left side of the range cooktop to the chassis, helping contain spills and fumes and ensuring a snug, stable fit. Replace a worn gasket to restore a clean seal and easier cleanup. What it does:

• Seals the left edge of the cooktop/main top to the range body
• Helps contain spills and moisture to prevent leaks below the top
• Maintains proper fit and reduces vibration or rattling
• Replaces torn, flattened, or missing gasket along the left side

• 1 left-hand maintop gasket

• Disconnect power; for gas models, also shut off gas. Allow all surfaces to cool.
• Lift or remove the maintop to access the gasket channel.
• Remove the old gasket and residue. Align the new gasket on the left side without stretching; press fully into place.
• Reassemble and verify an even seal before returning the appliance to service. Use cut-resistant gloves—sheet metal edges can be sharp.

This crystal retainer secures the clear lens on the appliance's control panel, keeping it properly seated and protected. Replacing a damaged or missing retainer restores a snug fit and helps prevent the lens from shifting or rattling.

• Holds the lens/crystal firmly in place to protect the window over the clock/timer or display
• Maintains proper alignment and a clean, finished appearance around the panel window
• Helps reduce vibration, rattling, or gaps around the lens area
• Failure may show as a loose or missing window, uneven fit, or buzzing from the panel

• Disconnect power at the breaker before servicing
• Access the retainer from behind the control panel; remove covers/screws as needed to reach the lens area
• Support the lens while removing/installing the retainer so it doesn't fall
• Wear gloves and eye protection; sheet-metal edges can be sharp

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw

Electronic range control (ERC) board that manages oven functions and user interface. Replacing this control restores oven operation, including temperature regulation, timers/clock, and keypad/display responsiveness. What it does:

• Controls bake, broil and timed cooking cycles and coordinates heating element operation.
• Manages the oven display, clock, timers and user inputs from the touchpad/keypad.
• Routes signals to relays/triacs to maintain the set temperature and cycle logic.
• Common symptoms indicating a faulty ERC: blank or unresponsive display, unresponsive controls, oven not heating or not cycling correctly, and erratic behavior.

• Disconnect power at the breaker before servicing to avoid shock or injury.
• Note and label wire locations or take a photo before disconnecting harnesses; reconnect connectors to original positions.
• After installation, restore power and verify oven functions (display, keypad, heating) before use.

This surface element limiter switch monitors burner temperature and opens the circuit if it overheats. It helps regulate element cycling for consistent cooking performance and, on many models, feeds the hot-surface indicator light.

• Monitors the surface element's temperature and interrupts power if overheating is detected
• Helps regulate element cycling to maintain safe operating temperatures
• Interfaces with the hot-surface indicator light on many models
• Common symptoms of a failed limiter: surface element won't heat, cycles off too soon, uneven heating, or hot-surface light stuck on or off

• Disconnect power at the breaker before servicing
• Access and mounting vary by model; typically installed at the surface element beneath the cooktop
• Transfer wires one at a time to the matching terminals; ensure snug connections
• Reinstall so the sensor face/clip contacts the element or bracket as originally positioned to ensure proper temperature sensing

This oven door latch secures the door to the oven frame as designed, restoring safe, reliable door locking. Replacing a worn or damaged latch helps ensure proper operation and prevents cycles from being interrupted by a door that won't latch.

• Locks and releases the oven door as required by the appliance's design
• Helps the oven operate safely by ensuring positive door engagement
• Can help resolve issues like a door that won't lock/unlock or a clean cycle that won't start due to latch problems
• Replaces bent, broken, or sticking latch mechanisms

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Access location varies by model
• Take photos of spring/linkage orientation and transfer any reused components from the original latch
• After installation, verify the door opens, closes, and locks/unlocks smoothly before running a cycle