Psh6pgzbess Parts

This freezer shelf trim replaces a damaged or missing edge piece on the freezer shelf. It attaches to the shelf/frame to provide a finished lip that helps contain items and restores the shelf's original fit and appearance.

• Provides the finished edge on a freezer shelf to help keep items from sliding off
• Attaches to the shelf/frame for a secure, correct fit
• Replace when cracked, warped, loose, or missing
• Common symptoms include a broken or jagged shelf edge, trim that won't stay attached, or items slipping off the shelf

• Unplug the refrigerator and remove items from the affected shelf
• Remove the shelf if needed; release and remove the old trim
• Align the new trim with the shelf/frame and press until fully seated and secure
• Do not force parts together; inspect the shelf/frame for damage before reassembly

This drain tube carries defrost water from the evaporator down to the drain pan, helping prevent puddles, leaks, and ice buildup. Replace a cracked, clogged, or missing tube to restore proper drainage and reduce recurring water issues.

• Routes defrost water from the evaporator drain to the drain pan
• Helps prevent water under drawers, on shelves, or on the floor
• Can address ice sheets on the freezer floor from a backed-up drain
• Replace if the tube is split, brittle, kinked, or obstructed

• Unplug the refrigerator and move it to access the rear; remove any back cover as needed
• Clear the drain opening and flush with warm water to remove ice/debris before installing
• Seat the tube fully on the drain outlet and route into the pan; avoid kinks and ensure free flow
• Restore power and check that water drains correctly into the pan

This defrost heater and bracket assembly melts frost from the evaporator during the automatic defrost cycle, restoring airflow and stable temperatures so your refrigerator and freezer cool as designed. What it does:

• Heats the evaporator coil at set intervals to clear frost and ice
• Keeps air passages open for consistent temperatures and efficient cooling
• Helps prevent excessive run times and ice buildup on the freezer back wall
• Failure signs can include heavy frost accumulation, weak/uneven cooling, or fan noise from ice

• One defrost heater pre-mounted to its bracket

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator behind the freezer's rear panel; safely defrost built-up ice before removal
• Note/photograph wire routing and connections; transfer like-for-like
• Avoid damaging evaporator fins and ensure the heater sits in the original position without touching plastic components

This ice dispenser auger drive mounts on the dispenser motor shaft and engages the ice bucket auger. Replacing a worn or stripped drive restores the connection so your refrigerator can move ice smoothly to the chute.

• Couples the dispenser motor to the ice-bin auger to rotate and move ice toward the chute
• On models with crushers, also drives the crushing mechanism
• Worn or rounded splines can cause little or no ice dispensing even though the motor runs
• May produce clicking/grinding noises from the door during dispense
• Visible cracking or play at the coupling indicates replacement is needed

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin to access the dispenser motor shaft in the freezer door
• Note the orientation; remove the old drive and seat the new drive fully on the shaft, transferring any original hardware if present
• Reinstall the ice bin, restore power, and test ice dispense

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Middle pan

This fixed freezer shelf restores a sturdy, level storage surface in the freezer compartment. Replace a broken or missing shelf to regain organization, correct spacing, and full storage capacity.

• Provides a fixed-position storage surface inside the freezer
• Helps keep items level, organized, and easy to access
• Restores proper spacing with adjacent shelves, drawers, or baskets
• Replaces a cracked, warped, or missing shelf

• Disconnect power before servicing; wear gloves to protect hands
• Empty the area, then align the shelf with the side-wall slots or supports
• Slide or place the shelf into the supports until fully seated and level
• Distribute weight evenly and avoid overloading after installation

This base grille mounts across the lower front of the refrigerator, covering and protecting the condenser area and leveling components while guiding airflow. Replacing a damaged or missing grille restores a clean appearance and the intended front-vent path.

• Covers the lower opening and helps keep debris away from condenser components
• Directs airflow through the front vents as designed
• Provides a finished, clean look at the toe-kick
• Helps prevent rattling when secured properly
• Common symptoms: cracked or scuffed grille, broken tabs, won't stay attached, missing piece

• Disconnect power and wear gloves to avoid sharp edges
• Open doors slightly to clear the grille ends
• Remove any screws or release spring clips and retain existing hardware
• Align tabs and snap/secure the new grille; ensure vents remain unobstructed

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This replacement bottom door hinge and pin assembly fits refrigerators. The lower hinge supports the door's weight and provides the pivot point, restoring smooth swing and proper alignment for a reliable close and consistent gasket seal.

• Serves as the door's lower pivot and load-bearing support
• Maintains alignment so the gasket seals correctly
• Restores smooth opening and closing after hinge/pin wear
• Common symptoms: door sagging or dragging, popping/squeaking at the hinge, gaps or poor sealing, door not staying closed

• Disconnect power and remove items from the door before servicing
• Support the door, remove bottom hinge fasteners, and lift the door off
• Position the new hinge and transfer any spacers/shims as found
• Reinstall the door, tighten hardware, and verify alignment and gasket seal

This assembly combines the refrigerator's internal water reservoir (tank) with its attached tubing to deliver chilled water to the dispenser. Replace a cracked or leaking tank to restore proper water flow and prevent leaks inside the fresh food compartment. What it does:

• Stores a reserve of water so dispensed water is cooled
• Routes water through the dispenser circuit via the attached tubing
• Typical failure symptoms: slow or no water from the dispenser, leaks or puddles inside the refrigerator, visible cracks or bulging in the tank
• Corrects issues caused by a frozen/split reservoir or brittle tubing

• One water tank with attached tubing assembly

• Unplug the refrigerator and shut off the water supply before servicing
• Access is typically behind the lower rear interior panel; remove drawers/shelves as needed
• Note original tube routing; cut tubing square and fully seat push-in fittings to prevent leaks
• Restore water and power, check connections, and dispense water to purge air from the system

This is the rear motor cover used in select GE refrigerators. It shields the motor area at the back of the compartment, helping direct airflow and protect the fan/motor assembly for reliable cooling performance.

• Protects the motor/fan area from debris and damage
• Helps channel air correctly through the compartment
• Cracks, broken tabs, or missing cover can lead to noise, poor airflow, frost, or temperature swings
• Restores proper fit and finish inside the compartment

• Unplug the refrigerator before servicing
• Remove shelves/bins obstructing access; retain screws/clips
• Carefully release locking tabs and transfer any reusable hardware
• Ensure the cover seats fully and resecure all fasteners before powering on

Keep water and ice flowing without internal filtration. This MSWF water filter bypass plug replaces the filter to seal the housing and route water properly to the dispenser and ice maker when a filter is not used.

• Installs in place of the MSWF filter to bypass filtration
• Maintains water flow to the dispenser and ice maker with no filter installed
• Helpful for troubleshooting restricted flow or when using an external filtration system
• Seals the filter head to help prevent leaks during bypass
• Note: No water is filtered while this plug is installed

• Shut off the water supply and dispense water to relieve system pressure
• Remove the MSWF filter; align and twist the bypass plug to lock into the filter head
• Restore water, check for leaks, and run the dispenser briefly to purge air
• Follow your refrigerator's instructions and use appropriate hand/eye protection