Pshss6rgxcdss Parts

This authentic OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's essential functions, such as adjusting and maintaining temperature. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced. To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and unscrew the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This replacement screw secures panels, brackets, and other hardware in your appliance. Installing a new fastener restores a tight, rattle-free fit when the original is missing, stripped, or corroded, helping keep components properly aligned.

• Fastens components, trim, and brackets to the cabinet or frame
• Replaces a missing, stripped, or rusted screw
• Helps reduce rattles, vibration, and loose panels or handles
• Maintains proper alignment of panels and hardware

• Disconnect power (and water/gas if applicable) before servicing.
• 12-24 thread, approximately 0.90-inch length; match to the original location.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Replace any additional damaged fasteners to ensure even clamping and a secure fit.

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

This bottom hinge pin supports and serves as the pivot for the refrigerator door. An accurate, tight-fitting hinge pin helps the door swing smoothly and seal properly to maintain temperature and reduce wear.

• Serves as the lower pivot point for the door on the bottom hinge
• Helps keep the door aligned for proper closing and gasket contact
• Replacing a worn pin can improve door movement and reduce stress on the hinge

• Unplug the appliance before servicing
• Support the door to relieve weight from the hinge before removing hardware
• Transfer any spacers/shims in their original order to maintain alignment
• Tighten fasteners securely and check door swing and seal after installation

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

This pan frame assembly supports and secures a refrigerator drawer, restoring proper alignment for smooth opening and closing. Replacing a worn or damaged frame helps prevent drawer sag, binding and uneven closure. What it does:

• Supports and aligns the bottom/produce drawer so it slides smoothly — symptoms: drawer tilts, binds or falls out.
• Secures the drawer to the cabinet, keeping stored items stable — symptoms: rattling or uneven gaps.
• Replaces cracked, warped or broken frame pieces that interfere with drawer operation.
• Helps restore correct drawer positioning to reduce wear on tracks and slides.

• Unplug the appliance or switch off its circuit before starting work to eliminate electrical risk.
• Remove drawer contents and slide the drawer out per the owner's manual before replacing the frame.
• Use basic hand tools; inspect tracks and mounting clips for damage and replace if needed.

This lid bumper cushions your washer lid where it meets the top panel, softening closure and protecting the finish. Replacing worn or missing bumpers reduces slamming and rattles for a quieter, smoother close.

• Cushions contact between the lid and top panel to reduce slamming noise
• Protects painted/enamel surfaces from chips and scratches at contact points
• Helps the lid sit level and minimizes vibration or rattling
• Replace if the bumper is missing, cracked, flattened, or hardened

• Disconnect power to the washer before servicing.
• Open the lid and locate the bumper(s) at the front corners (on the lid underside or top panel lip).
• Pull the old bumper straight out; clean the mounting hole.
• Press the new bumper firmly into the hole until fully seated and flush; test lid closure.

This electronic board powers and controls the light at the refrigerator's water/ice dispenser. Replacing it restores reliable illumination and proper on/off operation so you can clearly see the dispenser area during everyday use.

• Supplies regulated power to the dispenser light circuit for consistent brightness
• Responds to dispenser/control inputs to turn the light on and off
• A failing board can cause flickering or dim lighting
• Common symptoms include no dispenser light, intermittent light, or a light that stays on

• Disconnect power to the refrigerator before servicing
• Access the board behind the dispenser panel/escutcheon; remove trim carefully to avoid damage
• Handle the board by the edges and avoid static discharge; ensure connectors are fully seated

Pan frame assembly provides a sturdy support and positioning for the refrigerator's lower interior components, keeping drawers and pans level to help prevent misalignment and water pooling for smoother operation. What it does:

• Supports and aligns lower drawers, pans and slide tracks for reliable drawer movement
• Holds the drain/collector area in place so condensation and defrost water flow correctly
• Prevents sagging or uneven drawers that can cause binding or rubbing
• Reduces rattle or vibration from loose lower-cabinet parts

• Disconnect power to the appliance before starting any repair.
• Remove food, drawers and shelves as needed for access and to avoid damage.
• Use basic hand tools and follow OEM diagrams; align tabs and secure hardware snugly without over-tightening.
• Inspect surrounding clips and seals during replacement and replace any damaged components.

This manufacturer-specified screw fastens appliance panels, brackets, and internal components in place. Replace a missing or stripped fastener to restore a tight, rattle-free fit and reliable support at the original mounting points.

• Provides the correct fastener for securing covers, brackets, and assemblies
• Replaces lost, rusted, or damaged screws
• Helps resolve loose or vibrating panels and trim
• Maintains alignment of components and hardware

• Unplug the appliance; shut off water if working near supply lines
• Match the new screw to the original location; verify length and thread
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Keep removed hardware organized for reassembly

This dispenser recess grille sits in the ice/water dispenser well on the refrigerator door. It supports cups and lets minor drips pass through to the tray below, helping keep the area cleaner and more presentable.

• Provides a stable surface for cups and bottles at the door dispenser
• Slots allow drips to drain into the drip tray beneath
• Restores a clean, finished look to the dispenser area
• Common signs it's needed: cracked or warped grate, staining, missing piece, drips pooling on the surface

• For safety, disconnect power and shut off water before working near the dispenser area
• Lift out the old grille from the dispenser recess; some models use small locating tabs
• Clean and dry the recess and tray area before installing
• Seat the new grille flat and fully into position so it drains correctly

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

Includes 12 retainer rings.

This hex-head screw secures refrigerator components where a 12-24 x 7/8 in fastener is specified. Replacing a missing, stripped, or rusted screw restores a tight, reliable fit for brackets, panels, and assemblies and helps eliminate vibration and rattles.

• Fastens panels, brackets, and other assemblies in the refrigerator at locations calling for this size hardware
• Replaces worn, stripped, or missing screws to restore secure mounting
• Helps correct loose or misaligned components and reduce vibration noise
• OEM size: 12-24 thread, 7/8 in length; hex head

• Disconnect power and, if applicable, shut off the water supply before service
• Match the screw to the original location; replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use an appropriate nut driver or socket that fits the hex head

This shelf support replaces a broken or missing bracket that holds a refrigerator shelf in place. Restore a level, secure shelf surface and stop sagging or unexpected drops with a simple, like-for-like replacement.

• Supports the edge of an interior shelf and keeps it level
• Locks the shelf into the cabinet/liner mounting point
• Common signs to replace: shelf sags or tilts, won't stay positioned, support is cracked, loose, or missing
• Helps prevent shelf movement that can lead to spills

• Disconnect power and remove items from the affected shelf before starting.
• Note the position and orientation of the old support to match placement.
• Snap or screw the new support into the existing mounting point; transfer any reusable hardware.
• Reinstall the shelf and verify it seats level and secure.