Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.
Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Fix leaking water or a non-working ice maker with this refrigerator water inlet valve. Moderate DIY repair in 30-45 minutes with basic tools.
First, I had to remove the cover plate on the back of the refrigerator. Then I unscrewed the water inlet valve from the rest of the assembly. I then unplugged the electrical contacts by pulling them apart. There are two fittings on the valve. One has a nut on it. That one just needs the nut unscrewed, after which the pex tubing can be pulled out. The other one has a pex connection. This one can be separated by simultaneously pushing in on the fitting neck while pulling the pex tubing out. On... Read more
Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.
Replace solenoid, flapper door and recess spring. Really only needed solenoid, but other parts were so inexpensive and I knew I would already be in there. Read more
Fix a frozen evaporator coil with this defrost heater assembly. Restores proper cooling when frost buildup blocks airflow. DIY repair in 2-3 hours.
After doing a lot of web searching about the problem. It all came down to AppliancePartsPros.com. Watching the repair videos and learning what to do made the job a breeze. The only difficult problem was to thaw out the ice build up on the coils, which took 2 hours. The rest was easy. now I have a freezer/ fridge that is working like new. The total cost of the parts was less then having a repairman come out to look at it. AppliancePartsPros saved me a lot of money. Thanks! Read more
Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.
Ice won't dispense or drive spins freely? This auger drive coupler connects the motor to the ice bucket. Moderately difficult repair with basic tools.
The auger in ice bucket was frozen and locked in place (some how liquid water must have spilled inside and froze the shaft and bushing). When the motor was activated to deliver ice, the jam caused the motor shaft to strip the threads. With the threads stripped, there is no way (that I could find) to get the drive auger off of the shaft (btw, it is left-hand threaded). Apparently the Drive Auger is made of stainless steel - a harder metal then the motor shaft. To repair it, I removed the... Read more
Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.
Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more
Secures the ice chute flapper in your refrigerator door. Replace if cracked or missing to restore proper sealing and prevent frost buildup. Verify fit.
Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more
Replacement chill pan drawer that slides into refrigerator shelf rails. Needed when original pan is cracked, broken, melted, or missing. Exact fit.
Replaced it Read more
Fixed freezer shelf for side-by-side refrigerators. Replace a cracked, broken, or missing shelf to restore organized storage and spacing.
Ordered replacement shelves Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
White rear motor cover for refrigerator. Shields motor and fan area at back of compartment. Replace if cracked, broken, or missing to protect components.
Pictures on website were great. I ordered the part needed. Very easy to replace. Read more
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
I ordered the ice door assembly and a door recess spring and while I was working on that particular area the ice chute funnel that kept falling off on one side. It was all very easy, took maybe 15 mins in all. I watched the "how to" video that was posted and it was extremely helpful, giving me to confidence to do this myself. The only thing I might do different another time would be to take a look at the assembly before ordering parts. I didn't as I didn't want to keep opening the area up... Read more
Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.
Used screwdriver to take it off and screw the part back on. the customer service was great. Read more
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more