Pwe23kynfs Parts

• Fridge too cold
• Too warm
• Fridge runs too long
• Freezer too cold

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

Emptied the freezer and removed the drawers to allow access to the seal. Read more

Replaced filters Read more

We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more

The fix went great. I replaced the right-side door switch and it works great. The switch came as a three prong, and the original was a two prong. I matched the two prong wires with/on where they go on the switch, and it worked great. Next is the left door gasket. I am letting the new door gasket lay flat for a few days to see if the folded kinks/creases will relax out. They do instruct to use very hot water to get the folded shipping kinks out of it and will try that as a last resort. Read more

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

First let me say that we have been having a warm ff section since this refrigerator GE Mod GFE27GGDEWW since new. It was purchased in July of 2014, three repair under warranty,-thermistor,mother board, and a shrug of the shoulders, nothing wrong. the ff fan started making noise last week, and after doing some research saw that GE has a service bulletin REF03-18 updating the fan to WR60X29099. the install went well. new fan is quiet, seems to have more flow, but the ff section is still warm.The... Read more

Drop-In replacement crisper glass Read more

Ordered 2 door shelves from Appliance Parts Pros for my GE Profile refrigerator and was pleasantly surprised to receive the parts in two days. Parts were well packaged and fit perfectly. Was very helpful to be able to view my models parts diagram on-line to assure I was buying the right part. Read more

New spring Had trouble getting old spring pc out. drilled a small hole from bottom and pushed pc out with small paper clip. Worked good. Read more

My initial thought was we would have to purchase a new freezer since GE parts for our refrigerator was not available but I searched your website, yep it was available, I got on live chat to confirm the piece; it was a frictionless experience; I ordered that day it came 2 days later, my husband got out his tools and walaaaaah it’s fixed!! Love this experience, you are awesome! Read more

Not so easy! The fan is similar to a computer cooling fan but has a rounded housing that slips over a round condenser coil. It slides into a shoe bracket at the bottom. It should slide out towards the back of the refrig by approx 1/2 inch then pull up and out. But the fan shroud wraps around the condenser coil causing you not to be able to slide. You must first take a screw out that supports the condenser coil at the opposite end of the condenser "not easy to get to" then push the coil away... Read more

The fix went great. I replaced the right-side door switch and it works great. The switch came as a three prong, and the original was a two prong. I matched the two prong wires with/on where they go on the switch, and it worked great. Next is the left door gasket. I am letting the new door gasket lay flat for a few days to see if the folded kinks/creases will relax out. They do instruct to use very hot water to get the folded shipping kinks out of it and will try that as a last resort. Read more

Ordered part and replaced Read more

Easy fix with parts ordered. No tools. Parts fit perfectly! Best service. Parts arrived the next day!! Read more