Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Connects the drain hose to the washer drain outlet. Replace this coupling kit if cracked, broken, or leaking to restore a secure connection.
This is a flat steel washer with approximate dimensions of 28.65mm inner diameter, 39.6mm outer diameter, and 0.965mm thickness. It serves as a spacer or fastener component in various appliances, helping to distribute load and prevent loosening of bolted connections. Replace this washer if it is cracked, deformed, or corroded, which can cause rattling, loose fittings, or improper alignment of parts.
Washer won't agitate or makes grinding noises? This agitator shaft connects the agitator to the drive system. Moderate DIY repair, 30-45 minutes.
Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Usually ships within 4 - 14 days
Washer won't fill properly or overfills? This water level pressure switch senses fill levels and signals when to stop. Easy DIY fix for cycle timing issues.
I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it. I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair! Thank You Read more
Washer stuck between cycles or skipping rinse? This timer controls cycle sequence and duration. DIY repair typically takes 10-15 minutes with basic tools.
I knew the timer was bad. I went to the parts train website as i had done before. I found the part in just a few moments. It arrived in 2 days and I replaced the timer. 4 screws and 10 minutes was all that it took. Read more
Agitator broken or not turning clothes properly? This washer agitator assembly with built-in lint filter restores wash action. Easy DIY replacement.
Removed the old, and on with the new. Easiest repair I've ever done Read more
Spin tube assembly with drive spacer, bearing, and shaft seals. Replace if washer leaks from bottom or basket doesn't spin properly. Verify fit.
It was fairly difficult, but I watched and followed the Appliance PartsPros video and was able to get it done using the parts I purchased from APP. The leak has stopped (but I'm still watching after 5 loads). Read more
Seals the joint between your washer's outer tub and tub ring to prevent leaks. Replace if you notice water escaping during wash cycles.
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.
Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.
Rusted or missing motor shield letting debris reach your washer motor? This protective cover blocks foreign objects and secures the motor assembly. DIY repair.
The repair was simple. Having used Appliance Parts Pro in the past for much needed repair parts, I simply unplugged the machine, turned off the water and removed the drain hose and slid unit forward. I then removed the top control panel like last time, tilted the body forward and set it aside. I unfastened the upper hose to the water pump and slid what was left of the old shield out and slid the new replacement shield back into place then reattached the flex hose. The shield slipped right... Read more
Rear panel pad cushions and insulates the appliance's rear cabinet to reduce vibration, noise and rubbing against the back panel. Replacing a damaged pad helps stop rattles and protects internal components from wear. What it does:
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.