Rsw24 Parts

Replacement mounting screw for securing panels, brackets, and components in appliances. Needed when original fastener is missing, stripped, or damaged.

Wire tie secures and organizes internal wiring harnesses in your appliance. Replace if the original tie is broken, cracked, or missing during repairs.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This factory rivet is used to permanently fasten appliance panels and hardware. Replacing a worn or missing rivet restores a tight, rattle-free fit and keeps panels, brackets, or trim aligned as designed. What it does:

• Permanently secures sheet-metal or plastic parts where a rivet was originally installed
• Helps maintain alignment and rigidity; reduces vibration and rattling
• Replace if the original rivet is missing, loose, corroded, or drilled out during service
• Common symptoms include loose panel/trim pieces, buzzing noises, or visible gaps

• 1 rivet

• Disconnect power and shut off gas/water before servicing
• Remove the old rivet by carefully drilling through the rivet head; support nearby parts to prevent damage
• Install the new rivet with a suitable rivet tool; it seats fully and securely
• Wear eye protection when drilling or riveting; rivets are single-use and should not be reused

Does not come with wiring harness.

Fix a refrigerator that runs constantly or won't cool properly. This temperature control regulates cooling cycles. Moderate DIY repair for most models.

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

Flat plain washer that distributes load and spaces hardware on appliance assemblies. Replace if worn, missing, or needed for secure fastening.

Replacement hex nut secures panels, trim, and brackets in refrigerators. Needed when original nut is worn, missing, or stripped, causing loose components.

Fix intermittent water leaks or flow issues from your dispenser with a new ball sleeve. This guide supports the valve ball for a proper seal.

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

Color: Black

Ice maker shifting or loose? This mounting bracket secures your ice maker assembly in place to restore stable positioning and reliable ice production.

Freezer icing up or not defrosting? A faulty defrost timer prevents the automatic defrost cycle. This rotary timer restores proper defrost timing.