Scg903b Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Won't start

Replaced srark module Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

I had to take out the bottom drawer that holds pans. Disconnect the power and pull the oven out. Removed door, rear panel that held the screws for the side panel and lift up and out the side panel. After that it was straight forward as to replacing the hinge. Spent more time cleaning the florr where the oven was than installing the hinge. Read more

After researching on the internet I found I needed a new oven temperature sensor, and this site had the fastest delivery and a great price! I also like the videos telling you how to do the repair. My husband is the handyman, but has too many projects on his plate and the repairs looked simple. I did the temperature sensor all by myself when he wasn't even home, and the light socket replacement I only had trouble taking the old part out, so my husband pulled it out for me, but I did all the... Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more