Shp865wf5n Parts

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Installation Set is an OEM component specifically designed for installing Bosch dishwashers. It contains mounting fittings and hardware required to securely attach your dishwasher into place beneath countertops or cabinetry. 

Symptoms of a faulty installation set can include coming loose from mounting surfaces over time or missing, damaged parts that inhibit proper attachment. Replacement ensures accurate install fit.

Causes of a bad installation set include wear and tear related to repeated load shifting, impact, or mishandling leading to broken brackets/screws, or missing pieces after DIY installation attempts.

Causes of a bad installation set include:  

• Vibrations or rocking motions during wash cycles
• Drainage or plumbing connection issues  
• Installation difficulties requiring replacement parts

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 
 

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

This Bottom Case is the lower housing of the appliance. It forms the structural base that supports and protects internal components, helping restore proper alignment and stability when the original base is cracked, warped, or damaged.

• Provides the mounting base for key assemblies and exterior panels
• Helps protect internal parts from impact and debris
• Maintains chassis alignment to reduce vibration, rattling, or poor panel fit
• Replace if the original base is broken, warped, or otherwise compromised

• Disconnect power and, if applicable, shut off water before servicing
• Edges can be sharp; wear cut-resistant gloves and eye protection
• Access typically requires removing lower/outer panels; transfer any hardware or seals from the old base
• Before reassembly and testing

This replacement holder secures internal components in place to maintain proper alignment and reduce movement-related noise and wear. Use it when the original holder is cracked, deformed, or no longer holds parts firmly. What it does:

• Secures and supports internal assemblies to keep components correctly positioned.
• Reduces rattling, vibration and movement that can occur from loose parts.
• Replacing a worn or broken holder can prevent parts from shifting and causing intermittent operation.
• Use when the existing holder is visibly damaged, cracked, or fails to hold components tightly.

• Always disconnect power (and water, if applicable) before accessing the appliance.
• Remove surrounding panels, racks, or trim as needed for clear access.
• Reinstall using the original fasteners or clips; ensure correct orientation and secure fit without forcing parts.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

This holder is the mounting piece that secures a specific component inside your appliance. Replacing a cracked or missing holder restores proper support and alignment so the assembly stays stable and works as designed.

• Secures and supports the designated part in place
• Maintains alignment to help prevent vibration or rubbing
• A damaged holder can lead to loose or misaligned components
• Common symptoms: cracked/broken plastic, missing tabs, or the part no longer staying clipped/anchored

• Disconnect power and shut off water/gas before servicing
• Refer to your model's parts diagram for exact location and orientation
• Reuse original screws/clips/seals if they are not supplied with the replacement
• Do not overtighten fasteners into plastic; hand-snug to avoid stripping

The Leveling Leg is an OEM component specifically designed for Bosch dishwashers. This leg works to stabilize and balance the dishwasher evenly on any floor surface. 

The leveling leg is responsible for ensuring the dishwasher remains level during operation. Proper leveling is crucial for preventing excess vibration or noise, as well as allowing the dishwasher door to align correctly. 

Symptoms of a bad leveling leg can include:

• The dishwasher rocking or shuffling across the floor over time
• Excessive vibration or noise during wash cycles  
• The dishwasher door not closing or sealing properly
• Difficulty leveling the dishwasher 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.

The Control Panel is an OEM part for Bosch dishwashers. As the central interface, the panel houses all function buttons, cycle controls, and status lights.

The control panel maintains an attractive appearance while clearly presenting settings. Integrated options allow for customized washes tailored to any load.

Causes of a bad control panel can include exposure to steam, splashes, and cleaning chemicals over time. Daily touches introduce potential surface damage or circuitry corrosion. Accidental spills pose hazards.

Symptoms of a bad control panel include:

• Non-responsive or inaccurate touch buttons
• Faded graphics, lettering or illuminated indicators
• Loose panel or faulty mounting points
• Inaccurate cycle progress readings

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components