Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.
I went on your very user friendly website and looked up my bosch dishwasher. I love your diagrams and I felt confident that I could figure out what we possibly needed to get the door to close correctly and get the washer back working again. Your staff is courteous, service was fast and I would definitely recommend Appliance Parts Pros. Read more
This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.
Replaced the turbidity sensor. I watched the video on how to replace the sensor. It took me a little longer than what service rep. said. But I finely finished the repair and now my wife has been using the dishwasher for the past week. I kept checking for leaks but so far so good. Thank you Appliance Parts Pros for your help. I installed the sensor on 08/18/2020. Don Read more
Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.
Ordered new heater/thermostat piece. Read more
Replacement water feed tube that delivers water to the upper spray arm in your dishwasher. Replace if cracked, split at seams, or leaking due to wear.
After we saw that progressively our dishes were not getting clean we investigated the condition of the spray arms and this upper feed tube assembly. We found a huge crack on the side of this piece and new not enough water was getting to the arms. We also noticed a build up of soap and lime. So we ran a cycle of vinegar and sprayed the filters and arms with lime-off-sprayed them out with a air hose "completely". Many of the small pieces of lime will clog the holes in the spray arms. Attached the... Read more
Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.
Bacteria buildup in the venting assembly and drain hose. Replaced them and it's back to normal Read more
This pressure chamber is part of the water level sensing system in the dishwasher. It connects to the tub and the water level sensor, using air pressure changes to detect how much water has filled the machine so it knows when to stop filling. Replace this component if the dishwasher overfills, underfills, or displays water level error codes during a wash cycle.
Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more
Fix a dispenser door that won't stay closed or rinse aid light staying on. Complete assembly includes latch, spring, and gasket. DIY-friendly repair.
Replaced the dispenser. The video on your website was most helpful and made replacement very easy with the little tips to show removal and install of new part. Read more
The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance.
Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.
Symptoms indicating the need for a new Water Inlet Fill Hose include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Replaced the Water Inlet Valve and Drain Hose. Read more
O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.
WE replaced the drain pump and it still wouldn't drain sometimes. Finally we realized that the drain hose wasn't the correct bosch hose and the rubber was starting to bend and kink where it went through the hole to under the sink.So we bought the drain hose and replaced. Read more
The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.
Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.
Symptoms of a bad float include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Replaced the defective float switch. Read more
Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.
Wax motor for detergent/rinse-aid dispenser.
Took door off, saw that dispenser linkage was ok, I could open and close by hand, so figured the wax motor or the wiring to it were most likely the problem. I took off the wax motor ( actuator) and ran 120 volts to it via jumper wires, and it did not move at all, so figured good chance that was the problem. Found part # on your site, received new one quickly from you, put it in and works great. Thanks. Read more
Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.
Ordered a replacement control panel and installed it according to the AppliancePartsPros.com YouTube video. Read more
Fix a dishwasher door that won't close or latch properly. This latch and strike plate assembly restores secure door closure and safe operation.
Replaced check valve, was broken off and plugged the drain Read more
This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.
Ordered parts and put them on. Read more
Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.