Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Seals the detergent dispenser to prevent leaks and ensure proper release during wash cycles. Replace if detergent leaks or dispenser malfunctions.
Replaced dispenser. It was hard to snap into place. You don't need to order separate gasket it comes with it. Read more
Hose, with o - ring, shu (uc/12 & above)
This Sump to Float Hose is an OEM part for Bosch Dishwashers. It functions to carry water from the dishwasher sump to the float assembly. Continuous water flow and exposure to detergents can lead to wear or damage over time.
What Causes a Bad Sump to Float Hose: Exposure to chemicals and hot water, along with wear from water flow, can cause the hose to degrade or develop cracks.
Symptoms of a Bad Sump to Float Hose:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Used vids on youtube for steps on how to disassemble and install the pump; search "Bosch dishwasher circulation pump replacement". Also on AppliancePartsPro forums, a poster put up the Bosch "Dishwasher Service Training Manual" in .pdf. Search "Bosch dishwasher low pressure" on the forum. It's one of the post with the longest thread. Six pointers. 1. In another forum post, the poster noted that some hoses were brittle with age - and cracked when reinstalling. I had same issue (my washer is... Read more
Dishwasher won't start or keeps tripping the breaker? A damaged terminal box with melted connections is often the cause. Moderate DIY repair.
Purchased new replacement parts. The video was helpful. Thank you! Read more
The Hinge Lever (RH) is an OEM component specifically designed for Bosch dishwashers. This right-hand lever is a part of the dishwasher door hinge assembly, working to open and close the door during each use. Causes of a bad hinge lever can include wear and fatigue over thousands of opening and closing cycles. Damage can also potentially occur from any impact or denting of the door surface near the lever mechanism. Symptoms of an ineffective hinge lever include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.
Ordered the full hinge piece and an extra bushing. Was able just to slide the dishwasher forward a bit, lift the right side hinge off its seat and pop in the new bushing without disassembling. Fixed! I am retaining the full hinge piece in case of any future door incident but suspect I will never need it Read more
Replace your dishwasher's lower spray arm if it's cracked, broken, or worn. This rotating arm installs on the bottom of the tub to distribute water during wash cycles.
The wash arms and filters were plugged with calcium and no longer spraying. Needless to say this impacts cleaning. The replacement parts were top quality and fit perfect. This simple replacement of parts put new life in trusty Bosch. Read more
Fix a dishwasher that won't drain with this drain pump replacement. DIY-friendly repair takes 30-60 minutes. Includes step-by-step video guide.
We watched several videos on our Bosch dishwasher, and how to repair it. Then went to AppliancePartsPros.com, found the parts we needed, and watched their repair video. It took around 30 to 40 minutes to fix with the help of the video, thank you! Read more
Left-hand hinge lever for dishwasher doors. Assists door opening and closing through pivoting motion. Replace if cracked, broken, or damaged from overextension.
Replacement of hinges and door seal. Read more
Replace a missing or damaged junction box cover on your dishwasher. Protects power supply and control board wiring connections. Easy DIY repair.
Ordered parts and put them on. Read more
2 clamps included.
ORDERED TUBE AND CLAMPS Read more
Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.
Watched AppliancePartsPros video, disassembled the dishwasher and replace impeller and seals. Read more
This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.
I went on your very user friendly website and looked up my bosch dishwasher. I love your diagrams and I felt confident that I could figure out what we possibly needed to get the door to close correctly and get the washer back working again. Your staff is courteous, service was fast and I would definitely recommend Appliance Parts Pros. Read more
Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.
Ordered new heater/thermostat piece. Read more
Replacement water feed tube that delivers water to the upper spray arm in your dishwasher. Replace if cracked, split at seams, or leaking due to wear.
After we saw that progressively our dishes were not getting clean we investigated the condition of the spray arms and this upper feed tube assembly. We found a huge crack on the side of this piece and new not enough water was getting to the arms. We also noticed a build up of soap and lime. So we ran a cycle of vinegar and sprayed the filters and arms with lime-off-sprayed them out with a air hose "completely". Many of the small pieces of lime will clog the holes in the spray arms. Attached the... Read more
This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.
My micro filter was in pieces when I pulled it out. Read more
This pressure chamber is part of the water level sensing system in the dishwasher. It connects to the tub and the water level sensor, using air pressure changes to detect how much water has filled the machine so it knows when to stop filling. Replace this component if the dishwasher overfills, underfills, or displays water level error codes during a wash cycle.
Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more
Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.
Bacteria buildup in the venting assembly and drain hose. Replaced them and it's back to normal Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.